manualshive.com logo in svg

Takagi 110c, Installation Manual And Owner'S Manual

Share
Download
Takagi 110c Installation Manual And Owner'S Manual Download Page 21

21

  

Page

ELECTRICAL CONNECTIONS

• 

Follow the electrical code requirements of the local authority having 

jurisdiction. In the absence of such requirements, follow the current edition 

of the National Electrical Code ANSI/NFPA 70 in the U.S. or the current 

edition of CSA C22.1 Canadian Electrical Code Part 1 in Canada.

• 

When servicing or replacing parts within the water heater, label all wires 

prior to disconnection to facilitate an easy and error-free reconnection.  

Wiring errors can cause improper and dangerous operation.  Verify proper 

operation after servicing.

• 

Failure to observe these warnings could result in personal injury or loss of life.

WARNING

All concentric vent models come with a power plug.

1.  The water heater requires 

120 VAC, 60 Hz electrical power supply that is properly grounded

.

• 

A proper disconnect (i.e. on/off switch, power plug, etc.) controlling the main power to the water 

heater must be provided for service reasons.  (Must comply with local codes.)

2.  The use of a surge protector is recommended in order to protect the unit from power surges.

Installation

Installation Manual

Summary of Contents for 110c





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands