background image

 

TD9300 Installation and Configuration Manual

67

© Tait International Limited September 2018

Compliance Standards

T04-00002-xCxx 

(non-isolated)

T04-00002-xAxx 

(isolated v1)

T04-00002-xDxx 

(isolated v2)

Where applicable, this equipment has been tested and approved to the following standards:

EMC / RF

EN 301 489-1
EN 301 489-5
EN 300 113
CFR Title 47 Part 15
RSS-119
ICES-003
AS/NZS 4768

Safety

EN 60950-1
ANSI/UL 60950-1
CAN/CSA-C22 60950-1-07

Isolation and Immunity

N/A

EN 60255-5 Impulse 2kV (Serial, 
Ethernet, GPIO), Dielectric 2kVac 
(Serial, Ethernet, GPIO)
EN 61000-4-2 (ESD) Enclosure
±6kV Contact, ±8kV Air, Criteria A
EN 61000-4-3 (Rad. Imm.)
Enclosure 10V/m, Criteria A
EN 61000-4-4 (EFT) Serial and
Ethernet ±1kV, Criteria A
EN 61000-4-5 (Surge) Serial and
Ethernet ±1kV LE, Criteria A
EN 61000-4-6 (Cond. Imm.) Serial
and Ethernet, 10V, Criteria A
EN 61000-4-17 (Ripple) DC 10% @
24V, 10% @ 9V, Criteria A
EN 61000-4-29 (V.Int./Dip) DC 60%
@ 9V 100ms, 0% @ 9V 50ms,
Criteria A

EN 60255-5 Impulse 2kV (Serial, 
Ethernet, GPIO) 2.5kV (DC), 
Dielectric 2kVac (Serial, Ethernet, 
GPIO) 2.5kVDC (DC)
EN 61000-4-2 (ESD) Enclosure 
±6kV Contact, ±8kV Air, Criteria A
EN 61000-4-3 (Rad. Imm.) 
Enclosure 10V/m, Criteria A 
EN 61000-4-4 (EFT) Serial and 
Ethernet ±1kV, DC ±2kV

a

, Criteria A

EN 61000-4-5 (Surge) Serial and 
Ethernet ±1kV LE, DC ±2kV

a

 LE, 

Criteria A
EN 61000-4-6 (Cond. Imm.) Serial, 
Ethernet and DC 10V, Criteria A
EN 61000-4-12 (R.Wave) DC ±1kV

a

 

CM, ±0.5kV

a

 DM, Criteria A

EN 61000-4-16 (CM. Imm.) DC 
30V/300V, Criteria A
EN 61000-4-17 (Ripple) DC 10% @ 
24V, 10% @ 9V, Criteria A
EN 61000-4-29 (V.Int./Dip) DC 60% 
@ 9V 100ms, 0% @ 9V 50ms, 
Criteria A

Ingress Protection

IP40 - all orientations 
IP41 - front panel connector facing down

Environmental:

Low Pressure (Altitude)

MIL-STD-810G 500.5, Proc 2

High Temperature

MIL-STD-810G 501.5, Proc 1,2

Low Temperature

MIL-STD-810G 502.5, Proc 1,2

Temperature Shock

MIL-STD-810G 503.5, Proc 1

Humidity

MIL-STD-810G 507.5, Proc 2

Vibration

MIL-STD-810G 514.6, Proc 1 

Shock

MIL-STD-810G 516.6, Proc 1

a. Test conditions apply

Summary of Contents for TD9300










































































Reviews: