Tait T2000-A76 Operation Manual Download Page 27

Page: 27 / 30

March 2003

M2303-00-P00-805

PROGRESS

(despatcher radio to PC)

Unsolicited.

The PROGRESS message advises the PC of modem status when some significant change of state in the radio
occurs (typically during call processing).

It has the format :

p [PTYPE] [PARA1]

[PARAMETER]

Function

[PTYPE]

A two-digit string representing a decimal number in the range of 00 to 99 which
can identify the progress message category.

PARA1]

A single-digit number representing the message status.

[PTYPE] = 05

Receiver Busy

. This message indicates that the receiver has detected an RF sig-

nal on the current channel. This message is sent when the current channel
becomes busy.

[PTYPE] = 06

Receiver Not Busy

. This message indicates that the receiver no longer detects

an RF signal on the current channel. This message is sent when the current chan-
nel becomes available.

[PTYPE] = 07

PTT Mic Activated

. This message indicates that the PTT has been pressed. This

message is sent whenever the PTT is pressed in an attempt to transmit.

[PTYPE] = 08

PTT Mic Deactivated

. This message indicates that the PTT has been released.

This message is sent whenever the PTT is released after attempting to transmit.

[PTYPE] = 1D

SDM ACK

. This message indicates that an SDM ACK was received after the last

SDM sent. This only occurs if the modem receiving the SDM has SDM Auto ACK
enabled.
[PARA1] = 0 NO ACK RECEIVED
[PARA1] = 1 ACK RECEIVED

[PTYPE] = 1E

SDM Data Received

. This message indicates that the A76 received valid SDM

data with the correct SDM Data ID.
[PARA1] = 0 No SDM text message was included in the SDM. The [MESSAGE]
parameter was empty
[PARA1] = 1 The SDM included an SDM text message.

Summary of Contents for T2000-A76































Search results

Summary of Contents for T2000-A76

Reviews:

Related manuals for T2000-A76

Brands by name

Popular brands

Tait T2000-A76, Operation Manual

Search results

Summary of Contents for T2000-A76

Reviews:

Related manuals for T2000-A76

Brands by name

Popular brands