manualshive.com logo in svg

Tadiran Telecom TGW1E1-2G, User Configuration Manual

Share
Download
Tadiran Telecom TGW1E1-2G User Configuration Manual Download Page 56

TGWxE1-2G PRI (ISDN) Trunk                               
Gateways Series for Aeonix                                                                                                                    User Configuration Manual                                                                               

5-28 

Name 

Description 

STUN server 

This parameter appears when STUN is selected for NAT traversal.   

Set the IP or domain name of the STUN server. No default value. If the STUN server 
parameter is empty, the gateway will adopt the STUN server address configured at the 
factory.   

When selecting STUN for NAT traversal, the gateway will carry out STUN operations 
periodically according to the configured interval time of NAT refresh. 

RTPReceivingPort 

This parameter appears when STUN is selected for NAT traversal.   

The gateways will send the RTP receiving port selected here to the remote side.   

 

NAT port: Use NAT mapped port

，

which is obtained through STUN. 

 

Local port: Use local SIP and RTP port. 

Auto Provision 

Note: For detailed configurations, refer to 

Aeonix Administration Manual (Version 3

). 

Enable 

Select to use the auto provision function.

 

DHCP active 

Auto Provisioning Server (ACS) address is obtained by using DHCPoption66. 

Server 

Manually configure the ACS address, which can be the TFTP, FTP, or HTTP server. 

 

tftp://ACS address 

 

ftp:// ACS address 

 

http:// ACS address

 

Note: 

Aeonix version 3.1 uses http/s for auto provisioning 

Firmware upgrade 

Supports firmware download and update using ACS. 

Update mode 

The following modes are available. 

 

Power on: the gateway detects whether there are configurations and firmware to be 

updated when the device is powered on.   

 

Power on + Periodical: when the TGW is powered on, the gateway first checks whether 

there are configurations and firmware to be updated, and then periodically performs 
checking based on the set times. 

Interval ( minutes) 

When 

Power on+Periodical

 is set, this parameter specifies the interval for periodic 

automatic upgrades. 

TR069 

 

Server 

To use the TR069 network management, enter the IP address of the ACS.   

RTP Traverse 

 

Enable 

Select to enable the RTP traverse function. 

Remote Management 

The gateways support centralized auto provision. This will be supported as part of Aeonix version 3.

 

 

 

Summary of Contents for TGW1E1-2G


























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands