manualshive.com logo in svg

Tadiran Telecom TGW1E1-2G, User Configuration Manual

Share
Download
Tadiran Telecom TGW1E1-2G User Configuration Manual Download Page 25

TGWxE1-2G PRI (ISDN) Trunk                               
Gateways Series for Aeonix                                                                                                                    User Configuration Manual                                                                               

3-5 

3.3.5 Connecting the Power Cord 

Before connecting the power cord, make sure the AC power outlet has a protective earth contact and the 
earth contact of the AC power source is properly grounded. 

 

 

Please contact 

your manufacurer’s representative if the power LED does not light up after the power 

is turned on. Never install and uninstall the gateway or plug and unplug any cable on the gateway 
when the power is turned on.

 

 

Follow the steps to connect the power cord: 

Turn the switch of the AC power outlet to the OFF position. 

The TGWxE1-2G uses the shipped power cord to connect between the AC input at the rear of the chassis 
and the AC power outlet. 

 

3.3.6 Verifying Installation 

Installation verification is extremely important, because operations of the gateway depend on its stability, 
grounding, and power supply.   

Each time you turn on the power during the installation, verify that: 

 

Enough  clearance  has  been  reserved  around  the  ventilation  openings  of  the  gateway  and  the 
workbench/rack is stable enough. 

 

The protection ground is connected properly. 

 

Proper power is used as specified. 

 

The TGW gateway is correctly connected to the console terminal and other devices. 

 

Summary of Contents for TGW1E1-2G


























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands