background image

M037960E 

 

Safety Functions of Radio-control System

                      10                   

Safety Functions of Radio-control System

 

5. Alarm Function 

 

 

 

 
The following alarms sound when the system 
has a problem, when a wrong operation is 
made, or to call attention for proper operations. 
Take appropriate measures according to the 
following tables when the alarm sounds. 
 
 
 

 
 

(1) At the time of abnormal stop of the radio-control system: 
Warning sound    Beep (Three times) 
Warning timing   When the computer judges that serious trouble has occurred to the 

system 

Crane 
operation 

The radio-control operation is disabled. 

Measure 

Refer to the chapter of “Measures for Emergency Case” 

(2) At the time of a problem occurring when the operation lever is at the neutral position 
Warning sound    Beep (Three times) 
Warning timing   When the operation lever of the crane does not return to the neutral 

position even after the motion selection switch of the transmitter is 
returned to the neutral position. 

Crane 
operation 

The radio-control operation is disabled. 

Measure 

Refer to the chapter of “Measures for Emergency Case” 

(3) Battery exhaustion warning 
Warning sound    Two-tone alarm    (once) 
Warning timing    When the motion selection switch of the transmitter is operated under the 

low battery-voltage condition of the transmitter. 

Measure 

Refer to the chapter of “Battery Replacement for Transmitter” 

(4) At the set of emergency stop state 
Warning sound    Beep (Once) 
Warning timing    When the operation to set the emergency stop state is made. 
(5) At the release of emergency sop state   
Warning sound    Two-tone alarm (once) 
Warning timing    When the operation to release the emergency stop state is made. 

 

No alarm sounds when the speaker switch is turned “OFF”. Since it is an

important alarm, turn the speaker switch “ON” except for special cases.   
Operation should be made with special care when the switch needs to be turned off due
to noise prevention at nighttime operation and the like. 
In addition, make sure that the switch is returned to “ON” position after the operation.

     

SPEAKER

SPEAKER

ON

OFF

M22662E

Speaker 
switch

SPEAKER

SPEAKER

ON

OFF

Radio

Manual

   

Warning 

Summary of Contents for RCS-FT1





























Reviews: