Tadano GR-1600XL Service Manual Download Page 92

Page: 92 / 269

WY05-5030E

Y-8.

Operation Check (Crane Operation)

12. Outrigger slide plate adjustment

1. With the outriggers fully retracted, install the slide

plate and the plate into the outrigger box.

2. Adjust the slide plate with the bolts X so that the

slide plate is 2 mm (0.08 in) away from the upper
surface of outer outrigger box bottom plate.

3. If the slide plate is 2 mm (0.08 in) or more away,

make sure that the bolts X do not protrude beyond
the plane Z.

4. Tighten the bolt Y slightly to fix the slide plate.

Then tighten the nut of the bolt Y hard.

5. Tighten the nuts of the bolts X.

△

346-116-66000

Summary of Contents for GR-1600XL














































































































































































































































































Search results

Summary of Contents for GR-1600XL

Reviews:

Related manuals for GR-1600XL

Brands by name

Popular brands

Tadano GR-1600XL, Service Manual

Search results

Summary of Contents for GR-1600XL

Reviews:

Related manuals for GR-1600XL

Brands by name

Popular brands