background image

3.3.2.2

 

Flow rate sensor

The flow rate sensor (Fig.

 

14) measures the flow rate, ensuring a con-

stant flow rate can be set for the tap, regardless of the pressure.
The flow rate sensor is already connected and set ex-works.

3.3.2.3

 

Secondary circuit fill and drain cocks

The fill and drain cocks (Fig.

 

15) are used for filling and draining the

corresponding pipe sections.

3.3.3

 

Heat exchanger

Heat is exchanged between the primary and secondary circuits using

the heat exchanger (Fig.

 

16). A copper brazed heat exchanger is used

in the standard version. This can be replaced with a stainless steel

brazed heat exchanger if the water quality requires. Depending on the

design, the primary temperature must be at least 3

 

°C higher than the

domestic hot water temperature.

For information about the heat exchanger that is

suitable, see the data sheet “Drinking water thresh-

olds and material used for the plate heat exchanger”

in the Download Center (www.taconova.com).

Fig.

 

14:

 

Flow rate sensor

Fig.

 

15:

 

Fill and drain cocks

Fig.

 

16:

 

Heat exchanger

TACOTHERM FRESH PETA 2 / PETA 2 X

Functional description

V02.2020 11/2020

 

Item no. 215747

 

EA no. 1329

Operating instructions

27

Summary of Contents for TACOTHERM FRESH PETA 2













































































Reviews: