SystemAir SYSVRF WALL 15 Q Installation Manual Download Page 9

WIRE CONTROLLER

To wire controller  

DISPLAY BOARD

The reserved wire control function is indicated in broken 
line table,users can purchase the wire controller when 
necessary

7.2   Horsepower  set  

Horsepower code 

Code 

Capacity(Horsepower) 

2200W(0.8HP) 

5600W(2.0HP) 

4500W(1.5HP) 

3600W(1.2HP) 

2800W(1.0HP) 

7100W(2.5HP) 

Note: The horsepower
has been set before 
leaving the factory ,
no one should
modify it except the 
maintenance person.

0 1 

4 5 

8 9 

ENC1 

 

POWER_S

For set horsepower 

Toggle switch 

ENC1 

7.1   Terminal Board Diagram    

Please refer to the indoor unit wiring diagram for the wiring. 

NOTE 

The air-conditioners can connect with Central Control Monitor 
(CCM). Before operation, please wire correctly and set system 
address and network address of indoor units.

Single phase indoor unit 

INDOOR UNIT POWER 
220-240V

50/60Hz 

    (Conventional) 

XT1 

Y/G 

L  N 

RED 

BLUE 

WHI

T

E

 

BLU

E

 

BLA

C

BLA

C

YEL

L

OW  

To central control  

Monitor (CCM)  

COMM. BUS  

To outdoor  

COMM. BUS 

Please adopt the shielded twisted-pair wire,  

and connect the shielded layed to (E) 

X  

P  Q  (E) 

Y (E) 

GRAY 

XT1 

Y/G 

L1 L2 

RED 

BLUE 

INDOOR UNIT POWER 
220-240V

50/60Hz 

    (Special for UL) 

POWER IN 

POWER IN 

1500W(0.6HP) 

MAIN BOARD

8

installation manual 

7.3   Network address set 

1) Network address is set by communication of indoor and 
outdoor unit; the address is the same as indoor address, there 
is no need to set separately. 
2) The central control of indoor units can be done on outdoor 
unit, there is no need to control indoor unit separately, for 
details please refer to V4+ outdoor unit manual. 
3) For previous control of indoor units, the network can be set 
by connecting (X,Y,E) terminals, there is no need to set 
network address. The network can also be set by outer 
network module and main board (CN20). 

The system together have  64units(0-63), each one has a 
unique system addresscode. If two addresses are the  same 
in one system, operation will be abnormal.

Please switch off the power before setting, otherwise 
unexpected errors will occur.

CAUTION 

Summary of Contents for SYSVRF WALL 15 Q













Reviews: