SystemAir SYSVRF WALL 15 Q Installation Manual Download Page 10

9

installation manual 

7.4 Main board Code designation

● 

1 means factory test mode

● 

0 means auto addressing mode

      (default setting)

● 

1 means DC fan Is chosen 

● 

0 means AC fan Is chosen

 

00 means DC fan static pressure is 0

      (reserved)

● 

01 means DC fan static pressure is 1

      (reserved)

 

10 means DC fan static pressure is 2

      (reserved)

 

11 means DC fan static pressure is 3

       (reserved)

1 2 3 4 

S W 1 

O N 

1 2 3 4 

S W 1 

O N 

1 2 3 4 

S W 1 

O N 

1 2 3 4 

S W 1 

O N 

1 2 3 4 

S W 1 

O N 

1 2 3 4 

S W 1 

O N 

SW1 

definition 

● 

00 means shutting down the

        unit to"stop cold air" at 15 degrees

● 

01 means shutting down the

        unit to"stop cold air" at 20 degrees

● 

10 means shutting down the

        unit to"stop cold air" at 24 degrees

● 

11 means shutting down the

        unit to"stop cold air" at 26 degrees

● 

00 means the time of stopping 

        TERMAL fan is 4 minutes

● 

01 means the time of stopping 

        TERMAL fan is 8 minutes  

● 

10 means the time of stopping 

        TERMAL fan is 12 minutes 

● 

11 means the time of stopping 

        TERMAL fan is 16 minutes  

1 2 3 4 

S W 2 

O N 

1 2 3 4 

S W 2 

O N 

1 2 3 4 

S W 2 

O N 

1 2 3 4 

S W 2 

O N 

1 2 3 4 

S W 2 

O N 

1 2 3 4 

S W 2 

O N 

1 2 3 4 

S W 2 

O N 

1 2 3 4 

S W 2 

O N 

SW2 

definition 

 00 means temp.compensation

     value is 6 degrees under heat mode

 

10 means temp.compensation

       value is 4 degrees under heat mode

 

11 means temp.compensation

       value is 8 degrees under heat mode

 

01 means temp.compensation

       value is 2 degrees under heat mode

1   2  

S W 5 

O N 

1   2  

S W 5 

O N 

1   2  

S W 5 

O N 

1   2  

S W 5 

O N 

SW5 

definition 

 

1 means old display panel

 

0 means new display panel

 

1 means auto air blow under auto mode

 

0 means auto air blow under non-auto mode

reserved

1   2  3 

S W 6 

O N 

1   2  3 

S W 6 

O N 

1   2  3 

S W 6 

O N 

SW6 

definition 

without jumper "J1" for 
auto restart  function

with jumper "J1" for 
non-auto restart function

reserved

J1,J2 

definition 

J1 

J1 

J2 

Summary of Contents for SYSVRF WALL 15 Q













Reviews: