Sym Track Runner 200 Service Manual Download | Manualshive

Page: 216 / 221

background image

17. ELECTRICAL SYSTEM

17-19

Fuel Unit

Remove the seat.
Remove the fuel tank cap.
Remove the rear center cover.

Disconnect the coupler of the fuel unit.
Remove the fuel unit (4 bolts).

Caution

y

Great care shall be taken not to damage or

bend the float arm of the gauge.

When the float arm shifts to the F position or the E
position, the resistance measured shall be as
follows:

Position Resistance

E (Empty)

97.5~107.5

Ω

F (Full)

4~10

Ω

Connect the wiring to the fuel unit and the
ohmmeter as shown.

Connect the fuel unit coupler to the wire harness.
Turn on the main switch.
Move the float arm to verify the proper position the
fuel gauge needle indicates.

Arm Position

Needle Position

Up (Full)

F (Full)

Down (Empty)

E (Empty)

Caution

While conducting the test, turn on the direction
indication lamp to make sure that the battery is in
serviceable condition.

2 bolts

Fuel tank cap

Full

Empty

To this chapter contents

Fuel unit

«
...
214
215
216
217
218
...
»

Summary of Contents for Track Runner 200






























































































































































































































Reviews:

No comments

Related manuals for Track Runner 200

Brand: Baltmotors Pages: 58

Brand: BOMBARDIER Pages: 129

MAVERICK X3 Series 2017

Brand: Can-Am Pages: 155

Brand: Aosom Pages: 36

Brand: Applestone Pages: 134

Brand: Yamaha Pages: 60

DRIVE 2 SUPER HAULER 2019

Brand: Yamaha Pages: 60

Brand: HYOSUNG Pages: 133

Brand: Erde Pages: 4

Brand: Dometic Pages: 96

Engine Drive AY20

Brand: Miller Electric Pages: 2

Brand: KAYO MOTO Pages: 8

Brand: CRG Pages: 9

Brand: Yamaha Pages: 354

CRAZY CART SHUFFLE

Brand: Razor Pages: 12

Brand: Taylor-Dunn Pages: 232

1990 DS Gasoline Golf Car

Brand: Club Car Pages: 20

Brand: Club Car Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands