background image

 

 

5. Check gear box oil level--YEARLY 

 

Turn the power switch to the ―OFF‖ position.  Open the rear door and remove the 

rear battery.  Remove the gearbox oil plug through the access hole in the gearbox 
mounting bracket.  The oil level of each gearbox should be at the bottom of the plug 
hole.  If the oil level is low, fill the gearbox with 80W90 gear oil to the oil plug l Tighten 
the plugs and reinstall the rear battery.  

Do not remove the low oil plug.  Filling the 

gearbox only to the low oil plug level will result in severe gearbox damage 
 

Trouble shooting 

 

1.  Machine does not move 

Possible Cause 

Check/Repair 

Receiver fuse is blown 

Check fuse and replace with a 3 amp fuse if 
necessary 

Corrosion on battery 
connections 

Clean battery connections as outlined in the  
Maintenance section 

Discharged or faulty batteries 

Charge or replace batteries as necessary.   

Loose wire in electrical box 

Check connections in electrical box 

Battery charger not properly 
attached 

Check if the charger receptacle  wires are connected 
to batteries. 

Faulty power switch 

Check power switch.  Refer to Electrical service-
Checking the power switch. 

 

Summary of Contents for Boar Bot














































Reviews: