Your pool is equipped with (3) three special
warning
ledges. The (1) one ledge with
a large
warning
on top is to be installed by the entry point into the pool and is not to be
obstructed by any object such as your ladder. The (2) two ledges with the
warning
on
the inside are to be placed opposite the entry point into the pool with the warning fac-
ing the entry point.
THESE WARNINGS ARE NOT TO BE REMOVED UNDER ANY CIRCUMSTANCES
NOTE:
Your pools top ledge was not designed to be a walk around.
Caution everyone who uses your pool
NOT TO WALK OR SIT ON THE LEDGE!
If your pool is equipped with feature tape it is best to apply it to the ledges at this time.
20
INSTALLING LEDGES
AND PLACEMENT OF WARNING LABELS
16
No. 12 x 1/2”
Sheet Metal
Screw
Refer to the "Construction Close-ups" at the
beginning of these Instructions as indicated below:
B
E
A
D
A
C
B
C
D
C D E
E D C
E
B
B
A
A
WARNING
LEDGE
PLACEMENT
ENTRY POINT
Special
Instructions
for pools
with 9" Wide
Ledges
For pools with a 9" ledge, care should be
taken to assemble the ledge along the straight
sections of the pool in the manner shown
below. Along the straight sections of the pool,
use the short ledge sections and attach them
to the Buttress Top Plates using the screws
and holes illustrated on the left.
SCREW HOLE LOCATION GUIDE
16x10 18x12 24x12 24x15 30x15 33x18 39x18 45x18
OVAL
OVAL
OVAL
OVAL
OVAL
OVAL
OVAL
OVAL
FIG. A
(4" Ledge/ 4" Vertical)
B & D B & D B & D B & E B & E B & E B & E B & E
(6" Ext. Ledge/ 6" Old Ext. Vertical)
A & D A & D A & D A & D A & D A & D A & D A & D
FIG. B
(6" Ledge/ 6" Vertical)
E & C E & C E & C E & C E & C E & C E & C E & C
FIG. C
(6" Ledge/ 6" Vertical)
E & C E & C E & C E & C E & C E & C E & C E & C
FIG. D, E, G & H
(6" Ext. & 7" Ledge/ 6" Box Vertical)
A & D A & D A & D A & D A & D A & D A & D A & D
FIG. F
(9" Ledge/ 8" Box Vertical)
A & C A & C A & C A & C A & C A & C A & C A & C
Place ledges over the wall with each end resting on a top plate. Using the above chart
as a guide align the set of holes in the top plate as shown in the above drawing for
your size pool with the holes in the ledge and insert the No.12x1/2" Sheet Metal
Screw through the ledge and into the top plate. The actual screw holes that are used
does not affect the integrity of the pool. You may use the set of holes that line up best!
The ledge screws should not be tightened until all the ledges are in place and
the pool has been filled with water.
INSTALLING LEDGES ON BAR HARBOR
& RIO VISTA MODEL POOLS ONLY
Attention: You must use the 5/16” x 3/4” OD Stainless
Steel Washers with each Sheet Metal Screw to secure
the top ledges to the top plates. Failure to use the
washers may result in damaged ledges.
Place ledges over the wall with
each end resting on a top plate.
Align the set of holes in the top
plate as shown in the instructions
for your size pool with the holes
in the ledge and insert the
No.12x1/2" Sheet Metal Screw
through the washer and the
ledge and into the top plate.
1
1
1
3
2
2
B
C
C
D
E
D
E
B
1
2
3
