background image

14

THRU-THE-WALL SKIMMER

11

IMPORTANT!!  BEFORE CONTINUING WITH THIS STEP

YOU MUST KNOW WHICH TYPE OF THROUGH THE WALL SKIMMER

YOU WILL BE USING WITH YOUR POOL

Your pool wall has cutouts to accomodate both standard size skimmers and deluxe wide mouth 

skimmers.  If you have a wide mouth skimmer, you will be required to remove the entire cutout as
shown in figure 1.  To remove the section, you can use either tin snips or a hammer and knife as
shown in figure 3.  If you have a standard size skimmer, only remove the inside section of the cutout,
and place duct tape around the remaining scored sections as shown in figure 2.

If the through wall filter inlet and outlet holes are to be used, remove metal cutouts by breaking

perforations using a knife and hammer as shown.  Refer to skimmer manufacturer's instructions
for remainder of skimmer assembly.  

Make sure skimmer does not leak as this will corrode

the pool wall and cause a split in the wall that is not covered under the pool warranty.

It is recommended to coat the exposed metal on both sides with a clear lacquer or nail

polish to help resist rust and corrosion.

LARGE SKIMMER

CUT OUT ENTIRE AREA

SMALL SKIMMER

CUT INSIDE 

AREA

ONLY

1

2

3

On inside of wall, tape over

holes and slots that will not be

used with duct tape or any

other cloth tape.

Summary of Contents for Above Ground Swimming Pool





























Reviews: