manualshive.com logo in svg

Suzuki DF115B, Owner'S Manual

Share
Download
Suzuki DF115B Owner'S Manual Download Page 20

20

(6) Install the lock plate on the emergency stop

switch.

(7) Turn the main switch to the “ON & OFF”

position and then release it to the “PUSH
START/STOP” position to turn the Keyless
Start System OFF.
After that, do not perform any operation for
at least 30 seconds, while the system per-
forms passcode update.

PASSCODE CONFIRMATION

1. Confirm that the engine is stopped. 
2. Make sure the emergency switch lock plate

is in place.

3. Confirm the keyless fob is within the commu-

nication range of the Keyless Start System. 

4. Confirm the keyless fob is in ON mode.

(Refer to “Switching the communication
mode of the keyless fob” section.)

5. Turn the main switch to the “ON & OFF”

position and then release it. The main switch
automatically returns to the “PUSH START/
STOP” position. 
The buzzer on the engine control side emits
one (1) long sound while the buzzer on the
keyless control unit side emits two (2) short
sounds simultaneously. 

ON & OFF

ON & OFF

PUSH
START

STOP

PUSH
START

STOP

6. Within eight (8) seconds after performing

Step 5, start the following operation. 

(1) Turn the main switch to the “ON & OFF”

position and hold it for five (5) seconds or
longer, then release it to the “PUSH START/
STOP” position.
Repeat this operation for two more times.

(2) The LED on the keyless fob blinks once and

the buzzer sounds once. 
After that, the LED on the keyless fob blinks
to indicate the passcode by the number of
blinks, as shown in the illustration. 
This is indicated repeatedly.

NOTE:
The passcode indication will not start if Step (1)
is not performed within eight (8) seconds or the
operation fails.
In this case, turn the main switch to the “ON &
OFF” position and then release it to the “PUSH
START/STOP” position to turn the Keyless Start
System OFF. After that, retry the procedure
from Step 5.

7. After the passcode confirmation is com-

pleted, turn the main switch to the “ON &
OFF” position and then release it. The main
switch automatically returns to the “PUSH
START/STOP” position. The Keyless Start
System turns OFF and the passcode indica-
tion stops.  

ON & OFF

ON & OFF

Hold it for five (5) seconds. 

PUSH
START

STOP

PUSH
START

STOP

Example: In the case of passcode 1234

LED

Summary of Contents for DF115B












































































Reviews:

No comments

Brands by name

Popular brands

Load more brands