9
When “01” is keyed in, the value will appear on the display
as shown below:
LCard:01 Comd:F7
LCard:01 Comd:F7
LCard:01 Comd:F7
LCard:01 Comd:F7
LCard:01 Comd:F7
Op:36 Cd:01 Sc:__
Op:36 Cd:01 Sc:__
Op:36 Cd:01 Sc:__
Op:36 Cd:01 Sc:__
Op:36 Cd:01 Sc:__
Note that “Sc” is not used and stays blank. After the value is
entered at “Cd:”, press [ACK] or [Escape] to save the changes.
NOTE: If the [Escape] button is pressed before the value
at “Cd:” is entered, the changes will not be saved.
Verifying Data
• To verify the changes just entered, press and hold the [ACK]
button on the DRL-MX until this message is displayed:
Display Options
Display Options
Display Options
Display Options
Display Options
ACK:menu SEL:sel
ACK:menu SEL:sel
ACK:menu SEL:sel
ACK:menu SEL:sel
ACK:menu SEL:sel
• Press the [SELECT] button to view the system configuration;
this message will be displayed:
L01 #00
L01 #00
L01 #00
L01 #00
L01 #00
00
00
00
00
00
LCard Numb: 05
LCard Numb: 05
LCard Numb: 05
LCard Numb: 05
LCard Numb: 05
Press the [ACK] button to scroll forward through the configuration
displays until you reach option 36, or press the [SELECT] button
to scroll backwards through the configuration displays. Press
[ACK] and [SELECT] together to return to the Stand-By Mode.
Entering Commands
Commands are entered on the CPM2 keypad using the following
format: LCard; Comd; Op; Cd; Sc
• LCard: “Line Card” is the Line Card number; enter a
hexadecimal number from 01 to 0E for Line Cards 1 through
14.
• Comd: “Command” is the Command; enter a command from
the list above
• Op: “Option” indicates a function that is part of a command;
the following sections of this manual will explain which
commands have options. Enter a 2-digit hexadecimal number
• Cd: “Code” is the code or value to be programmed for the
Option; enter a 2-digit hexadecimal number
• Sc: “Second Code” is a code or value that is only used with
SCADA commands; if required, enter a 2-digit hex number
Entering Data
The following is how to enter the Programming Password and
program an option in the F7 Options Programming section:
• Press and hold the [C] button on the CPM2 until the CPM2
displays the following message:
Enter PASS-WORD
Enter PASS-WORD
Enter PASS-WORD
Enter PASS-WORD
Enter PASS-WORD
****
The default password is “CAFE”. Enter the password using
the CPM2 keypad.
• When the password is entered, the CPM2 will display this
message:
LCard:__ Comd:__
LCard:__ Comd:__
LCard:__ Comd:__
LCard:__ Comd:__
LCard:__ Comd:__
Op:__ Cd:__ Sc:__
Op:__ Cd:__ Sc:__
Op:__ Cd:__ Sc:__
Op:__ Cd:__ Sc:__
Op:__ Cd:__ Sc:__
• Enter the Line Card number. In this example, Line Card 01
will be used. When “01” is keyed in, the number will appear
on the display as shown below:
LCard:01 Comd:__
LCard:01 Comd:__
LCard:01 Comd:__
LCard:01 Comd:__
LCard:01 Comd:__
Op:__ Cd:__ Sc:__
Op:__ Cd:__ Sc:__
Op:__ Cd:__ Sc:__
Op:__ Cd:__ Sc:__
Op:__ Cd:__ Sc:__
• Enter the Command number. In this example, the F7 Options
Programming command will be used. When “F7” is keyed
in, the command will appear on the display as shown below:
LCard:01 Comd:F7
LCard:01 Comd:F7
LCard:01 Comd:F7
LCard:01 Comd:F7
LCard:01 Comd:F7
Op:__ Cd:__ Sc:__
Op:__ Cd:__ Sc:__
Op:__ Cd:__ Sc:__
Op:__ Cd:__ Sc:__
Op:__ Cd:__ Sc:__
• Enter the Option number. In this example, Option [36] will
be changed. When “36” is keyed in, the Option will appear
on the display as shown below:
LCard:01 Comd:F7
LCard:01 Comd:F7
LCard:01 Comd:F7
LCard:01 Comd:F7
LCard:01 Comd:F7
Op:36 Cd:__ Sc:__
Op:36 Cd:__ Sc:__
Op:36 Cd:__ Sc:__
Op:36 Cd:__ Sc:__
Op:36 Cd:__ Sc:__
• Enter the value to be programmed at Option 36. In this example,
01 will be programmed at Option [36] to enable it.
firealarmresources.com
