background image

  FCC compliance information 

20 

FCC compliance information 

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.   
Operation is subject to the following two conditions: 

(1) This device may not cause harmful interference, and 

(2) This device must accept any interference received, including interference that may cause undesired operation. 

 

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment 
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause 

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If 

this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off 

and on, the user is encouraged to try to correct the interference by one or more of the following measures: 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

Modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment under FCC rules.   
 

 

This appliance and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. 

A minimum separation distance of 20 cm must be maintained between the antenna and the person for this appliance to satisfy the RF 

exposure requirements. 

 

 

EU Declaration of Conformity (CE)   

This product is CE marked according to the provisions of the R&TTE Directive(1999/5/EC). Hereby, Suprema Inc. declares that this product is 

in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. This device is Class 1 radio equipment 

under the European Radio and Telecommunications Terminal Equipment (R&TTE) Directive (1999/5/EC).   

 

 
For more information, contact us at the following contact information. 

Suprema Inc. 

Website: 

https://www.supremainc.com

 

Address: Parkview Tower F16, 248, Jeongjail-ro, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea (Jeongja-dong 6) 

Tel: +82-31-783-4502 / Fax: +82-31-783-4503 

 
 

 

 

 

 

Summary of Contents for BioStation A2























Reviews: