Supero H8SSL-i2 User Manual Download Page 12

Page: 12 / 68

1-6

H8SSL-i2 User’s Manual

Serverboard Features

CPU

• Single AMD dual-core Opteron 1000 Series 64-bit processor in a 940-pin mi-

croPGA ZIF (AM2) socket

Memory

• Four dual/single channel DIMM slots supporting up to 8 GB of unbuffered ECC/

non-ECC DDR2-800/667/533 SDRAM

Note: Refer to Section 2-4 before installing.

Chipset

• ServerWorks

HT-1000

Expansion Slots

• One (1) 64-bit, 133 MHz PCI-X slot (3.3V)

• Two (2) 32-bit, 33 MHz PCI slots (5V)

BIOS

• 4

Firmware

Hub

AMIBIOS

Flash ROM

• APM 1.2, DMI 2.3, PCI 2.2, ACPI 1.0 (ACPI 2.0 is BIOS supported), Plug and

Play (PnP)

PC Health Monitoring

• Onboard monitors for CPU core voltage, +3.3V,

5V,

12V, +5V standby and

battery voltage

• Fan status monitor with ﬁ rmware/software speed control in BIOS

• Watch

Dog,

NMI

• Environmental temperature monitoring via BIOS

• Power-up mode control for recovery from AC power loss

• System

resource

alert

• Hardware BIOS virus protection

• Auto-switching voltage regulator for the CPU core

Summary of Contents for H8SSL-i2





































































Search results

Summary of Contents for H8SSL-i2

Reviews:

Related manuals for H8SSL-i2

Brands by name

Popular brands

Supero H8SSL-i2, User Manual

Search results

Summary of Contents for H8SSL-i2

Reviews:

Related manuals for H8SSL-i2

Brands by name

Popular brands