manualshive.com logo in svg

Supermicro SUPERSERVER 6018TR-T, User Manual

Share
Download
Supermicro SUPERSERVER 6018TR-T User Manual Download Page 81

Chapter 5: Advanced Motherboard Setup

5-29

Figure 5-6. SuperDoctor 5 Interface Display Screen  (Health Information)

SuperDoctor 5

The Supermicro SuperDoctor

®

 5 is a hardware and operating system services 

monitoring program that functions in a command-line or web-based interface in 

Windows and Linux operating systems. The program monitors system health 

information such as CPU temperature, system voltages, system power consumption, 

fan speed, and provides alerts via email or Simple Network Management Protocol 

(SNMP). 

SuperDoctor 5 comes in local and remote management versions and can be 

used with Nagios to maximize your system monitoring needs. With SuperDoctor 5 

Management Server (SSM Server), you can remotely control power on/off and reset 

chassis intrusion for multiple systems with SuperDoctor 5 or IPMI. SD5 Management 

Server monitors HTTP, FTP, and SMTP services to optimize the effi ciency of your 

operation.

Note:

 The default User Name and Password for SuperDoctor 5 is admin / admin.

Summary of Contents for SUPERSERVER 6018TR-T

















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands