Supermicro SUPERSERVER 6018R-TD, User Manual

Page: 61 / 77

Chapter 7: BIOS
7-23 7-22
S
UPER
S
ERVER 6018R-TD User's Manual
Above 4G Decoding (Available if the system supports 64-bit PCI decoding)
Select Enabled to decode a PCI device that supports 64-bit in the space above 4G
Address. The options are
Disabled and Enabled.
SR-IOV (Available if the system supports Single-Root Virtualization)
Select Enabled for Single-Root IO Virtualization support. The options are Disabled
and Enabled.
Maximum Payload
Select Auto for the system BIOS to automatically set the maximum payload value
for a PCI-E device to enhance system performance. The options are
Auto , 128
Bytes, and 256 Bytes.
Maximum Read Request
Select Auto for the system BIOS to automatically set the maximum size for a read
request for a PCI-E device to enhance system performance. The options are
Auto ,
128 Bytes, 256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes, and 4096 Bytes.
ASPM Support
Use this item to set the Active State Power Management (ASPM) level for a PCIe
device. Select Auto for the system BIOS to automatically set the ASPM level based
on the system configuration. Select Disabled to disable ASPM support. The options
are Disabled and Auto.
Warning: Enabling ASPM support may cause some PCI-E devices to fail.
MMIOHBase
Use this item to select the base memory size according to memory-address map-
ping for the IO hub. The options are
56T , 48T, 24T, 3T, and 2T.
MMIO High Size
Use this item to select the high memory size according to memory-address mapping
for the IO hub. The options are
256G , 128G, 512G, and 1024G.
CPU1 SLOT4 PCI-E x8/CPU1 SLOT5 PCI-E x8/CPU1 SLOT6 PCI-E x8 (/CPU2
SLOT7 PCI-E x8
Select Enabled to enable Option ROM support to boot the computer using a de-
vice installed on the slot specified by the user. The options are Disabled, Legacy ,
and EFI.
Onboard LAN Option ROM Type
Select Enabled to enable Option ROM support to boot the computer using a device
installed on the slot specified by the user. The options are Legacy and EFI.
Onboard LAN1 Option ROM/Onboard LAN2 Option ROM
Use this option to select the type of device installed in LAN Port1 or LAN Port2
used for system boot. The options for LAN1 Option ROM are Disabled,
PXE , iSCSI,
and FCoE. The options for LAN2 Option ROM are Disabled and PXE.
Onboard NVMe1 Option ROM/Onboard NVMe2 Option ROM (For X10DRD-
iNT)
Use this item to select the type of device to be installed in NVMe Connector 1 or
NVMe Connector 2 for system boot. The options for both NVMe connectors are
Disabled and
EFI .
Onboard Video OPROM
This feature controls how the system executes UEFI (Unified Extensible Firmware
Interface) and Legacy Video OPROM. Select Legacy to boot the system using a
legacy video device installed on the motherboard for system boot. The options are
Disabled,
Legacy , and EFI.
VGA Priority
Use this item to select the graphics device to be used as the primary video display
for system boot. The options are
Onboard and Offboard.
Network Stack
Select Enabled to enable PXE (Preboot Execution Environment) or UEFI (Uni-
fied Extensible Firmware Interface) for network stack support. The options are
Disabled and Enabled.

Super IO Configuration
Super IO Chip AST2400
 Serial Port 1 Configuration/Serial Port 2 Configuration
Serial Port 1/Serial Port 2
Select Enabled to enable the onboard serial port specified by the user. The options
are Enabled and Disabled.
Device Settings
This item displays the base I/O port address and the Interrupt Request address of
a serial port specified by the user.
Change Port 1 Settings/Change Port 2 Settings
This feature specifies the base I/O port address and the Interrupt Request address
of Serial Port 1 or Serial Port 2. Select Auto for the BIOS to automatically assign
the base I/O and IRQ address to a serial port specified.