Supermicro SUPERSERVER 6018R-TD, User Manual

Page: 37 / 77

Chapter 5: Advanced Serverboard Setup
5-15 5-14
S
UPER
S
ERVER 6018R-TD User's Manual
NIC1/NIC2 LED Indicators
The NIC (Network Interface Controller)
LED connection for LAN port 1 is located
on pins 11 and 12 of JF1, and the LED
connection for LAN port 2 is on pins 9 and
10. Attach the NIC LED cables here to
display network activity. Refer to the table
on the right for pin definitions.
NIC1/2 LED
Pin Definitions (JF1)
Pin# Definition
9 NIC 2 Activity LED
10 NIC 2 Link LED
11 NIC 1 Activity LED
12 NIC 1 Link LED
Power Fail LED
The Power Fail LED connection is lo-
cated on pins 5 and 6 of JF1. Refer to
the table on the right for pin definitions.
PWR Fail LED
Pin Definitions (JF1)
Pin# Definition
5 3.3V
6 PWR Supply Fail
Universal Information LED
Connect an LED cable to pins 7 and
8 of JF1 to use the Overheat/Fan Fail/
Power Fail and UID LED connections.
The red LED on pin 7 provides warnings
of overheat, fan failure or power failure.
The blue LED on pin 8 works as the
front panel UID LED indicator. Refer to
the tables on the right for pin definitions.
Universal Information LED
Pin Definitions (JF1)
Pin# Definition
7 Blue UID LED
8 OH/Fan Fail/Power Fail
OH/Fan Fail/PWR Fail
LED Status (Red LED)
State Definition
Off Normal
On Overheat
Flashing Fan Fail
Reset Button
The Reset Button connection is located
on pins 3 and 4 of JF1. Attach it to a
hardware reset switch on the computer
case. Refer to the table on the right for
pin definitions.
Reset Button
Pin Definitions (JF1)
Pin# Definition
3 Reset
4 Ground
Power Button
The Power Button connection is located
on pins 1 and 2 of JF1. Momentarily
contacting both pins will power on/off the
system. To turn off the power when the
system is in suspend mode, press the
button for four seconds or longer. Refer
to the table on the right for pin definitions.
Power Button
Pin Definitions (JF1)
Pin# Definition
1 Signal
2 Ground
Universal Serial Bus (USB)
Four Universal Serial Bus ports (USB
0/1, USB 2/3) are located on the rear
I/O panel. In addition, an internal USB
header provides two front-accessible
USB connections (USB 4/5). One
Type A connector (USB6) also sup-
ports front panel USB connection.
(Cables are not included.)
Serial Ports
Two COM connections (COM1 and COM2) are provided on the serverboard. COM1
is located on the rear I/O panel. COM2, located close to Slot4 (PCI-E 3.0 x8),
provides front access support.
Back Panel USB 0/1, 2/3 (2.0)
Pin Definitions
Pin# Definition Pin# Definition
1 +5V 5 +5V
2 USB_PN1 6 USB_PN0
3 USB_PP1 7 USB_PP0
4 Ground 8 Ground
Front Panel USB 4/5 (2.0), Type A USB
6 (2.0)
Pin Definitions
Pin# Description
1 VBUS
2 SSRX-
3 SSRX+
4 Ground
5 SSTX-
6 SSTX+
7 GND_DRAIN
8 D-
9 D+
Ethernet LAN Ports
Two Gigabit LAN ports supported by the Intel i350 are provided on the rear I/O panel.
In addition, a dedicated IPMI LAN port, supported by the AST2400 BMC (Baseboard
Management Controller), is also provided to provide LAN support for IPMI 2.0.