Supermicro SuperServer 2028BT-HTR+ User Manual Download Page 3 | Manualshive

Page: 3 / 128

background image

iii

Preface

Preface

Preface

About this Manual

This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the SuperServer. Installation and
maintenance should be performed by experienced technicians only.

Please refer to the server specifications page on our Web site for updates on

supported memory, processors and operating systems (

www.supermicro.com

).

This manual may be periodically updated without notice. Please check the
Supermicro Web site for possible updates to the manual revision level.

Warnings

Special attention should be given to the following symbols used in this manual.

Warning!

Indicates high voltage may be encountered when performing

a procedure.

Warning!

Indicates important information given to prevent equipment/

property damage or personal injury.

«
1
2
3
4
5
...
»

Summary of Contents for SuperServer 2028BT-HTR+

































































































































Reviews:

No comments

Related manuals for SuperServer 2028BT-HTR+

Brand: Samsung Pages: 7

Redbooks ServeRAID-MR10k

Brand: IBM Pages: 48

D-811_002-NXS-SAG

Brand: NOMACHINE Pages: 19

SCHROFF 11850-016

Brand: nvent Pages: 18

UniServer E3200 G3

Brand: H3C Pages: 401

Brand: TAPKO Pages: 2

Brand: PRIMERGY Pages: 87

Brand: ACTi Pages: 11

SuperServer 5037C-i

Brand: Supermicro Pages: 88

Brand: Altos Pages: 104

Brand: LOVATO ELECTRIC Pages: 5

ProLiant DL100 G2 DPSS

Brand: HP Pages: 155

NetStorage 6000

Brand: HP Pages: 192

ProLiant DL100 G2 DPSS

Brand: HP Pages: 44

Brand: Dell Pages: 396

Brand: Dell Pages: 180

EqualLogic PS6010

Brand: Dell Pages: 57

PowerVault 700N

Brand: Dell Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands