Superior FVDA18M Installation And Operation Instructions Manual Download Page 4

Superiorfireplaces.US.com

126900-01_B 

4

PRODUCT IDENTIFICATION

Hearth Kit Model                                                                                  
Serial Number                                                                                    
Log Set Model                                                                                   

Figure 1 - Product Identification

Grate

Burner 

Pan

Burner 

Manifold

Burner 

Clamp

Grate Steps

LOCAL CODES

Install and use fireplace with care. Follow all local codes. In the ab-

sence of local codes, use the latest edition of The National Fuel Gas 

Code ANSI Z223.1/NFPA 54*.
*Available from:

American National Standards Institute, Inc.

25 West 43rd Street, 4th floor

New York, NY 10036

National Fire Protection Association, Inc.

1 Batterymarch Park

Quincy, MA 02169-7471

PRODUCT FEATURE

ON/OFF SAFETY VALVE/PILOT

Unit is tested and approved to 

ANSI Z21.60

 and 

CSA 2.26

 as a vented 

decorative appliance. It is supplied with the parts and instructions 

to convert to propane/LP gas use.

UNPACKING

 CAUTION: Do not remove the metal data plates 

from the burner pan. The data plates contain important 

warranty and safety information.

1.  Remove logs, hearth kit, pan materials, and hardware from carton. 
2.  Remove all protective packaging applied to logs and base for 

shipment.

3.  Check appliance for any shipping damage. If appliance is dam-

aged contact IHP at Superiorfireplaces.US.com for replacement 

parts before returning to dealer.

COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS

These appliances are approved for installation in the US state of 

Massachusetts if the following additional requirements are met:
•  Install this appliance in accordance with Massachusetts Rules 

and Regulations 248 C.M.R. Sections 4.00 through 8.00.

•  Installation and repair must be done by a plumber or gas fitter 

licensed in the Commonwealth of Massachusetts.

•  The flexible gas line connector used shall not exceed 36 inches 

(92 centimeters) in length.

•  The individual manual shut-off must be a T-handle type valve.

Summary of Contents for FVDA18M





















Reviews: