Superior FVDA18M Installation And Operation Instructions Manual Download Page 1

Installation and Operation Instructions
Gas Log Vented Decorative Appliance

Models

P/N 126900-01    Rev  B  11/2016

PFS

®

US

P126900-01

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
This appliance may be installed in an aftermarket permanently located, manufactured (mobile) home, where not 

prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating plate. This 

appliance is not convertible for use with other gases.

 WARNING: This is a gas-fired appliance. It uses air (oxygen) from the room in which it is installed. Provisions 

for adequate combustion and ventilation air must be provided. Refer to the National Fuel Gas Codes, ANSI 

Z233.1/NFPA 54, Air for Combustion and Ventilation.

 WARNING: This appliance is for installation only in a solid-fuel burning masonry or UL127 factory-built 

fireplace, constructed of noncombustible material, and connected to a working flue. (See page 5 for minimum 

flue opening.)

IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate, or service 

this log set. Improper use of this log set can cause serious injury or death from burns, fire, explosion, electrical 

shock, and carbon monoxide poisoning.

 WARNING: 

FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious injury, death, or property damage.

 

 Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other 

appliance.

 

 WHAT TO DO IF YOU SMELL GAS: 

•  Do not try to light any appliance. 
•  Do not touch any electrical switch; do not use any phone in your building. 
•  Leave the building immediately.
• Immediately call your gas supplier from a neighbor’s phone.  Follow the gas supplier’s instructions. 
•  If you cannot reach your gas supplier, call the fire department.

 

Installation and service must be performed by a qualified installer, service agency or the gas supplier.

REPORT NO. F09-167

MODEL

CAT. NO.

FVDA18M

F0215

FVDA24M

F0217

FVDA30M

F0219

FVSA18M

F0221

FVSA24M

F0223

Summary of Contents for FVDA18M





















Reviews: