background image

General Information

900994-00K, 07/2021 

Innovative Hearth Products
DRL2000 & DRL3500 Series Direct-Vent Gas Fireplaces

6

APPLIANCE INSTALLATION, SERVICE, AND MAINTENANCE NOTICES

 WARNING 

Improper installation, adjustment, alteration, service or maintenance can cause injury or 

property damage. Refer to this manual. For assistance or additional information consult a 

qualified installer, service agency or the gas supplier.

 AVERTISSEMENT 

Une installation, un réglage,une modification, une réparation ou un entretien mal effectué 

peut causer des dommages matériels ou des blessures. Voir la notice de l’utilisateur qui 

accompagne l’appareil. Pour de l’aide ou des renseignements supplémentaires, consultez 

un installateur, un technicien agréé ou le fournisseur de gaz.

Only trim kit(s) supplied by the manufacturer shall be used in the installation of this fireplace.

Seules des portes certifiées pour cet appareil doivent être utilisées.

These appliances must not be connected to a chimney or flue serving a separate solid fuel 

burning appliance.

Any change to this appliance and/or its operating controls is dangerous. Improper installation 

or use of this appliance can cause serious injury or death from fire, burns, explosion or 

carbon monoxide poisoning.

CARBON MONOXIDE POISONING: Early signs of carbon monoxide poisoning are similar to 

the flu with headaches, dizziness and/or nausea. If you have these signs, obtain fresh air 

immediately. Turn off the gas supply to the appliance and have it serviced by a qualified 

professional, as it may not be operating correctly. Some people are more affected by carbon 

monoxide than others, including pregnant women, people with heart or lung disease or 

anemia, those under the influence of alcohol, and those at high altitudes.

Turn off gas and electrical power to the appliance and allow it to cool before cleaning or 

servicing the appliance.

If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s barrier 

for this appliance.

Si l’écran est endommagé, il doit être remplacé par celui fournit par le fabricant de cet 

appareil.

For use with barrier(s) Part No(s). F4248 (35” Models), F4249 (45” Models) and F4250 (55” 

models). Follow installation instructions.

Reinstall any barrier removed before operating the appliance. The barrier is designed to 

reduce the risk of burns from hot glass. Do not operate the appliance without the barrier 

installed.

f i r e - p a r t s . c o m

Summary of Contents for DRL2000 Series













































































Reviews: