background image

 
 

 

 

TECHNICAL PASSPORT INSTALLATION and OPERATION MANUAL 

24-EN

the  housing will  be  deactivated.  If  the  controller  fails  to reach  parameters  required 
for  entering  into  the  operation  mode  within  30  min.  from  activation  of  the  fire-up 
function, the „Unable to fire up“ message will appear on the display. In such a case, 
the fire-up cycle needs to be restarted. 

 

10.1.2.  Operation  –  The  operation  cycle  is  the  basic  functionality  of  the  controller. 
The  power  of  fan  is  regulated  by  the  user.  If  the  temperature  rises  above  the  set 
temperature the suspension mode will be activated. 

 

10.1.3.  Suspension  mode  –  this  mode  will  be  activated  automatically  if  the 
temperature  is  equal  or  higher  than  the  set  temperature.  In  that  case,  in  order  to 
ensure  smooth  decrease  of  temperature  of  circulating  water  it  is  necessary  to 
properly set operation times of the fan. 
 
10.1.4. Damping - if boiler temperature drops by 2°C below the fire-up threshold and 
fails  to  rise  above  this  value  for  30  min.  (default  damping  time),  the  controller  will 
switch  to  the  damping  mode.  While  in  this  mode,  the  fan  is  deactivated  and  the 
display shows “Damping”.  

 

 
10.2. Main page 

During  normal  operation  (in  only  CH  mode)  the  LCD  display  shows  the  main  page 
which presents the following information: 

Boiler temperature (on the left side of the display) 

Set temperature (on the right side of the boiler) 

Symbol of non-operating fans (*) 

Mode of operation - in the lower right corner appear in capital letters initials 

of the respective operating mode: 
– residential heating; R – parallel pumps; В – DHW priority; L – summer mode. 
This  screen  allows  for  quick  change  of  the  set  temperature,  by  the  means  of  PLUS 
and MINUS buttons. Pressing down MENU moves the user to the 1st level menu, the 
display then shows the first two rows of the menu. In each menu the user can move 
up and down by the means of PLUS and MINUS buttons. Pressing down MENU moves 
the user to the consecutive menu or enables a specific function. EXIT moves the user 
back to the root menu. 

 

In case of voltage loss, the controller ceases to operate. When power is 
restored,  the  controller  returns  to  operation  with  previously  set 
parameters using its built-in memory.

 

Summary of Contents for BURNiT Magna WBS-A 450









































Reviews: