SunSynk SUN-25K-SG01HP3-EU-BM2 Installer Manual Download

Page: 65 / 74

Page | 65

Hybrid Inverter | Installer Manual

Error Code

Description

Solutions

F56

DC bus bar voltage is
too low

Battery low voltage
1. Check if the battery voltage is too low.
2. If the battery voltage is too low use the PV or grid
to charge the battery.
3. Check the battery BMS

Important:

Especially with Lithium batteries, ensure

that the batteries Max. discharge current or power
specification is the same or higher than the inverter
specification.

F64

Heat sink high-tem-
perature failure

Heat Sink temp is too high
Check if the working environment temperature is too
high.
Turn off the inverter for 30 minutes and restart.

Fault

Information

Instruction

Fault

Information

Structure

F01

DC_Inversed_Failure

F33

AC_OverCurr_Fault

F02

DC_Insulation_Failure

F34

AC_Overload_Fault

F03

GFDI_Failure

F35

AC_NoUtility_Fault

F04

GFDI_Ground_Failure

F36

AC_GridPhaseSeque_Fault

F05

EEPROM_Read_Failure

F37

AC_Volt_Unbalance_Fault

F06

EEPROM_Write_Failure

F38

AC_Curr_Unbalance_Fault

F07

GFDI_Fuse_Failure

F39

INT_AC_OverCurr_Fault

F08

GFDI_Relay_Failure

F40

INT_DC_OverCurr_Fault

F09

IGBT_Failure

F41

AC_WU_OverVolt_Fault

F10

AuxPowerBoard_Failure

F42

AC_WU_UnderVolt_Fault

F11

AC_MainContactor_Failure

F43

AC_VW_OverVolt_Fault

F12

AC_SlaveContactor_Failure

F44

AC_VW_UnderVolt_Fault

F13

Working_Mode_change

F45

AC_UV_OverVolt_Fault

F14

DC_OverCurr_Failure

F46

AC_UV_UnderVolt_Fault

F15

AC_OverCurr_Failure

F47

AC_OverFreq_Fault

F16

GFCI_Failure

F48

AC_UnderFreq_Fault

F17

Tz_COM_OC_Fault

F49

AC_U_GridCurr_DcHigh_Fault

F18

Tz_Ac_OverCurr_Fault

F50

AC_V_GridCurr_DcHigh_Fault

F19

Tz_Integ_Fault

F51

AC_W_GridCurr_DcHigh_Fault

F20

Tz_Dc_OverCurr_Fault

F52

AC_A_InductCurr_DcHigh_Fault

F21

Tz_GFDI_OC_Fault

F53

AC_B_InductCurr_DcHigh_Fault

Summary of Contents for SUN-25K-SG01HP3-EU-BM2











































































Search results

Summary of Contents for SUN-25K-SG01HP3-EU-BM2

Reviews:

Related manuals for SUN-25K-SG01HP3-EU-BM2

Brands by name

Popular brands

SunSynk SUN-25K-SG01HP3-EU-BM2, Installer Manual

Search results

Summary of Contents for SUN-25K-SG01HP3-EU-BM2

Reviews:

Related manuals for SUN-25K-SG01HP3-EU-BM2

Brands by name

Popular brands