background image

  

 

  

 

 

 

 

 

 

 

  

 

  

 

 

 

 

 

 

 

Page | 42

Hybrid Inverter | Installer Manual

5.11.  Generator & Battery Page

To configure battery charging settings, click on the BATTERY icon and then on ‘Batt Charge’.

What this page displays:

 

ƒ

Generator start voltage/SOC %.

 

ƒ

Grid power start voltage/SOC %.

 

ƒ

Float V is the voltage at which a battery is maintained after being fully charged.

 

ƒ

Absorption V the level of charge that can be applied without overheating the battery.

 

ƒ

Float V for an AGM battery is 55.20V.

 

ƒ

Absorption V is for an AGM battery is 57.60V.

 

ƒ

Equalization V for an AGM battery is 58.80V.

 

ƒ

Equalizing charge/overcharge to remove sulphate crystals that build-up on the plates over 
time on lead-acid batteries.

What you can do from this page:

 

ƒ

Tick ‘Gen Charge’ to charge the batteries from the gen I/P.

 

ƒ

Tick ‘Grid Charge’ to charge the batteries from the grid I/P.

 

ƒ

Tick ‘Gen Signal’ signal to auto-switch a relay box.

 

ƒ

Tick ‘Grid Signal’ signal to auto-switch a relay box.

Do not alter these settings too many times on the same battery as it may damage 
the battery.

Summary of Contents for SUN-25K-SG01HP3-EU-BM2











































































Reviews: