SunStar SC9200 Series User Manual Download Page 30

Page: 30 / 37

25) UPPER BLADE CHANGE

1) Loosen the screw

①

. Move the fixed blade holder

②

to the

left to the utmost limit. Tighten the screw

①

temporarily.

2) Then remove the screw

③

and movable blade

④

. To install

new movable blade, turn the hand pulley until movable blade
holder reaches to the lowest position within the movement
range. (Figure A) The cutting section of movable and fixed
blade is overlapped about 0.5~1.0mm depending on the
overedge width.

3) Overlap the cutting section of the movable/fixed blade to

cross the center point of the upper blade(A) and the center
point of the fixed blade

⑥

like Figure B.

4) Put the thread between the movable and the fixed blade.

Check the cutting motion by turning the manual pulley.

26) LOWER BLADE CHANGE

1) Loosen the screw

①

. Move the fixed blade holder

②

to the

left to the utmost limit. Tighten the screw

①

temporarily.

2) Loosen the screw

⑤

, remove the fixed blade

⑥

. Install new

fixed blade depending on the order 3), 4) above mentioned (1
UPPER BLADE CHANGE).

CAUTION The edge of the fixed blade is located 0~0.3mm
below the front face of the needle plate to install new fixed
blade.

27) OVEREDGE WIDTH ADUSTMENT

1) Loosen the screw

①

. Move the fixed blade holder

②

to the

left. Tighten the screw

①

temporarily.

2) Loosen the screw

⑦

, move the movable blade clamp

⑧

from

side to side as required. Install the movable/fixed blade
depending on the order 3), 4) above mentioned (1 UPPER
BLADE CHANGE).

The edge of the fixed blade is located
0~0.3mm below the front face of the
needle plate to install new fixed blade.

Caution

[Figure 52]

[Figure 53]

[Figure 54]

[Figure 55]

⑥

④

⑥

④

⑥

⑤

⑦

⑧

③

④

②

①

0~0.3mm

0.5mm~1.0mm

Figure

Summary of Contents for SC9200 Series






































Search results

Summary of Contents for SC9200 Series

Reviews:

Related manuals for SC9200 Series

Brands by name

Popular brands

SunStar SC9200 Series, User Manual

Search results

Summary of Contents for SC9200 Series

Reviews:

Related manuals for SC9200 Series

Brands by name

Popular brands