SunStar SC9200 Series User Manual Download Page 33 | Manualshive

Page: 33 / 37

background image

33

①

①

To adjust the front/rear of the upper feed dog

1) loosen the bar lifter

①

. Set the adjustment lever

②

to the

maximum value on the indicator.
Tighten the bar lifter

①

.

2) Turn the pulley until it moves to the end of the upper feed dog

rear side.

3) loosen the screw

③

. Adjust the gap (a) from the end of the

needle plate front side to the end of the upper feed dog front
side by moving the upper feed dog.

4) Adjust the screw

③

.

②

②

To adjust the pressure of the upper feed dog

1) loosen the nut

①

.

2) control the pressure with using the adjustment screw

②

.

The pressure should be enough to move the texture exactly
but the upper feed dog should not damage the texture.
Check the standard measures on the table 9.
Turn to (+) direction to increase the pressure.
Turn to (-) direction to decrease the pressure.

Table 9) The Height of the Pressure Adjustment

Screw for the Upper Feed Dog

Model

a

SCT9214-03/333

25.5

SCT9316-03/233

24

SCT9316-A04/435K

23.5

Table 8)

Model

a

SCT9214-03/333

23.5

SCT9316-03/233

18

SCT9316-A04/435K

18.5

N

No

ottee..

If the pressure is too low, irregular feed and noise could
be happened.

②

①

②

①

③

①

②

[Figure 64]

[Figure 65]

[Figure 66]

[Figure 67]

[Figure 68]

«
...
31
32
33
34
35
...
»

Summary of Contents for SC9200 Series






































Reviews:

No comments

Related manuals for SC9200 Series

Brand: Passap Pages: 25

Brand: Clarke Technology Pages: 54

Brand: Clemas & Co Pages: 7

Brand: Truvox Pages: 12

Brand: Olivetti Pages: 130

Brand: Factory Cat Pages: 26

Brand: Singer Pages: 51

Brand: FONESTAR Pages: 16

Cover Stitch Wide

Brand: Singer Pages: 13

Brand: Count Pages: 27

Brand: Garudan Pages: 67

Brand: Unicum Pages: 115

Brand: JUKI Pages: 40

Decor Excel 2 5024

Brand: Janome Pages: 41

UNI_NIGHTVISION_01

Brand: UNIPRODO Pages: 9

Brand: Advance acoustic Pages: 12

Brand: Advance acoustic Pages: 38

Brand: Muratec Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands