manualshive.com logo in svg

SunStar SC9200 Series, User Manual

Share
Download
SunStar SC9200 Series User Manual Download Page 17

17

3) THREAD TENSION ADJUSTMENT

To fasten the thread (to increase the thread tension), turn the
thread tension cap clockwise. To loosen the thread (to decrease
the thread tension), turn each thread tension cap
counterclockwise. Each thread tension should be set light as
possible but adjust the tension to form the beautiful stitches. 

4) PRESSER FOOT PLACEMENT/REMOVAL

To remove the presser foot,
1) Turn the hand pulley to the highest point. 
2) lower the presser lifting lever

①

and then rotate the presser

foot arm

②

toward the side.

To change the presser foot, 
1) Turn the hand pulley to the highest point.
2) lower the presser lifting lever

①

and then reach the presser

foot arm

②

in good condition.

5) PRESSER FOOT PRESSURE ADJUSTMENT 

The presser foot pressure should be set light but transfer the
sewing material precisely and adjust the pressure to form regular
stitches. 
1) Loosen the adjusting nut

①

to adjust the presser foot pressure

and tighten the adjusting screw

②

as much as you need. 

2) Fix the adjusting nut

①

by tightening after adjusting. 

[Figure 16]

[Figure 17]

[Figure 18]

Strong

Weak

Adjust  the  thread  tension  according  to
the sewing materials and the thread. 

Reference

Weak

Strong

①

②

①

②

Summary of Contents for SC9200 Series






































Reviews:

No comments

Brands by name

Popular brands

Load more brands