SunStar KM-570BL User Manual Download

Page: 20 / 29

Adjusting the auxiliary presser foot

※

Loosen the pressure-adjusting screw

④

and the bracket-fastening screw

⑤

※

Adjust the bracket-fastening screw

⑤

so that the auxiliary presser foot

①

rise about 10.5 mm from the needle plate

top when the pressure lifter

③

is raised.

(After adjustment, be sure to fasten the bracket-fastening screw

⑤

first, and then adjust the pressure-adjusting

screw

④

※

Affter the adjustment of the height of the auxiliary presser foot

①

, adjust the upper feed presser foot

②

Adjusting the upper feed presser foot

※

Loosen up and down crank clamp screw

⑥

when the pressure lifter

③

is down.

※

Move the needle bar close to its highest position.

※

Adjust the height of the upper feed presser foot

②

to the sewing materials.

(2) Adjusting the height of the strokes of both different

[Figure 31]

②

①

⑥

④

⑤

③

10.5mm

Summary of Contents for KM-570BL






























Search results

Summary of Contents for KM-570BL

Reviews:

Related manuals for KM-570BL

Brands by name

Popular brands

SunStar KM-570BL, User Manual

Search results

Summary of Contents for KM-570BL

Reviews:

Related manuals for KM-570BL

Brands by name

Popular brands