manualshive.com logo in svg

SunStar KM-570BL, User Manual

Share
Download
SunStar KM-570BL User Manual Download Page 19

19

10) Adjusting feed dog height

Turn the pulley so that the feed dog 

①

is positioned at its hight to adjust the feed dog 

①

. Loosen the fork clamp screw 

④

of

the feed dog base as in Figure 29 and move the feed dog base up and down so that the feed dog protrudes about 1 mm from

the needle plate top. After adjustment, fasten the clamp screw 

④

firmly.

11) Adjusting the auxiliary presser foot and the upper feed presser foot

※

Both the auxiliary presser foot and the upper feed presser foot move up and down.

※

It is normal that both of them move up and down to the same height.

※

Take the following steps either to adjust the stroke of both to be the same or to make one of the two adjusted lower or

higher, depending on sewing materials.

(1) Adjusting the strokes of both to be the same

A) The vertical motion range of the supplementary presser foot

①

and the upper feed presser foot

②

is 2~6mm.

B) Loosen the adjusting hinge screw 

③

.

C) Vertically adjust the hinge screw

③

depending on sewing fabric. When the motion range is set large, move the

adjusting hinge screw

③

upward. Otherwise, move the adjusting hinge screw downward.  

[Figure 29]

①

②

About 1 mm

③

④

[Figure 30]

①

②

③

6mm

6mm

Increase

Decrease

Summary of Contents for KM-570BL






























Reviews:

No comments

Brands by name

Popular brands

Load more brands