SunStar KM-1640BL-7 User Manual Download Page 4

Page: 4 / 36

Contents

1. Machine safety regulations

---------------------------------------------------------------------

1-1) Transporting machine

---------------------------------------------------------------------------

1-2) Installing machine

---------------------------------------------------------------------------------

1-3) Repairing machine

--------------------------------------------------------------------------------

1-4) Operating machine

-------------------------------------------------------------------------------

1-5) Safety devices

-------------------------------------------------------------------------------------

1-6) Caution mark position

----------------------------------------------------------------------------

1-7) Contents of marks

--------------------------------------------------------------------------------

2. Names of main parts

-------------------------------------------------------------------------------

3. Specification

-----------------------------------------------------------------------------------------

3-1) Sewing machine

---------------------------------------------------------------------------------

3-2) Peripheral Automation Devices Specifications(options)

------------------------------

4. Installation

---------------------------------------------------------------------------------------------

4.1) Installation place

---------------------------------------------------------------------------------

4.2) Machine delivery

---------------------------------------------------------------------------------

4.3) Bending the machine backwards

-----------------------------------------------------------

4.4) Table drawing

------------------------------------------------------------------------------------

4.5) Installation of Sewing Machine Body

-------------------------------------------------------

4.6) Trial run (Pedal operation)

--------------------------------------------------------------------

4.7) Check for machine stop position

------------------------------------------------------------

4.8) Reverse button function (for automatic trimming type)

--------------------------------

4.9) Installation of Automatic Knee Lifter Solenoid(options) and Power Switch Box

--------

5. Preparations for sewing

------------------------------------------------------------------------

5.1) Installing needle

---------------------------------------------------------------------------------

5.2) Bobbin Insertion and Removal

---------------------------------------------------------------

5.3) Winding lower thread

---------------------------------------------------------------------------

5.4) Inserting upper thread

--------------------------------------------------------------------------

6. Sewing

--------------------------------------------------------------------------------------------------

6.1) Sewing

---------------------------------------------------------------------------------------------

6.2) Adjusting thread tension

-----------------------------------------------------------------------

7. Inspecting and checking

----------------------------------------------------------------------

7.1) Regular Check Points

--------------------------------------------------------------------------

7.2) Cleaning

-------------------------------------------------------------------------------------------

Summary of Contents for KM-1640BL-7





































Search results

Summary of Contents for KM-1640BL-7

Reviews:

Related manuals for KM-1640BL-7

Brands by name

Popular brands

SunStar KM-1640BL-7, User Manual

Search results

Summary of Contents for KM-1640BL-7

Reviews:

Related manuals for KM-1640BL-7

Brands by name

Popular brands