SunStar KM-1640BL-7 User Manual Download Page 13

Page: 13 / 36

[Fig. 4-5]

[Fig. 4-6]

[Fig. 4-7]

4.5.3) OP Panel

Fix the operating panel

①

to the bracket

②

using a

bolt

③

and then fix it to the upper part of the rear arm

using a bolt

④

4.5) Installation of Sewing Machine Body

4.5.1) Installation of Hinge, Oil Pan and Machine

1Insert the hinge rubber

①

into the table. After inserting the oil tray in the middle of head supporting rubber B

②

shown in the figure 1, install it into the table. Insert the machine head hinge

③

into the bed holes. By inserting it into the

hinge rubber

①

, stand the machine on the head support rubber A

④

and the head support rubber B

②

4.5.2) Installation of Knee Lift Pad

A. Insert a knee lift pad

②

in a knee support shaft

point

①

assembled in the oil pan and adjust the

position for the user to fix it.

B. Insert a knee lift rod cap

③

in the hole of the oil

pan as shown in the figure.

②

①

③

oil tray (oil fan)

②

①

④

③

①

③

①

②

③

④

Summary of Contents for KM-1640BL-7





































Search results

Summary of Contents for KM-1640BL-7

Reviews:

Related manuals for KM-1640BL-7

Brands by name

Popular brands

SunStar KM-1640BL-7, User Manual

Search results

Summary of Contents for KM-1640BL-7

Reviews:

Related manuals for KM-1640BL-7

Brands by name

Popular brands