manualshive.com logo in svg

SunStar KM-1640BL-7, User Manual, Page: 29 / 36

Share
Download
SunStar KM-1640BL-7 User Manual Download Page 29

29

■

In case of running vertically the auxiliary presser foot and the upper feed presser foot at the same height

A. Adjusting the auxiliary presser foot

- 

Loosen the presser bar pressure adjustment screw

①

and the bracket fixing screw

②

.

- 

Adjust vertically the bracket fixing screw

②

so that the auxiliary presser foot

④

goes up by 8mm from the upper

side of the needle plate when the presser bar lifter

③

is up.

- 

When the adjustment is finished, fix tightly the bracket fixing screw

②

and adjust adequately the pressure

adjustment screw

①

.

- 

After adjust height of the auxiliary presser foot

④

, adjust upper feed presser foot. 

B. Adjusting the upper feed presser foot

- 

Place the thread take up at the lowest position and lower the presser bar lifter

③

.

- 

Open the rubber cover

⑤

of the upper cover and loosen the clamp screw

⑥

.

- 

A different adjustment of vertical running amount between the auxiliary presser foot

④

and the upper feed presser

foot

⑧

is possible by adjusting the presser foot vertical move crank

⑦

.

- 

When the adjustment is finished, fix tightly the clamp screw

⑥

of the vertical move crank, and place the rubber

cover

⑤

.

[Fig. 8-10]

8.10) Adjusting feeding amount of auxiliary

presser foot

The normal proportion of feeding amount between the feed

dog and the auxiliary presser foot is 1:1.  You can adjust the

feeding amount of the auxiliary presser foot in accordance

with the conditions of materials in use.  As in Figure 8-11,

loosen the nut

①

and move upward the presser foot vertical

move control shaft

②

, and the feeding amount becomes

smaller.  If you move it downward, the amount increases.

Be sure to tight the nut

①

when the adjustment is finished.

[Fig. 8-11]

①

②

④

⑤

⑥

8mm

⑧

③

⑦

①

②

Summary of Contents for KM-1640BL-7





































Reviews:

No comments