background image

 

 

 

TROUBLESHOOTING 

PROBLEM 

CAUSE 

SOLUTION 

Treadmill will not start 

 
Not plugged in 

 

Plug cord into outlet 

Safety Key not inserted 

Insert Safety Key 

Running speed inaccurate 

Not calibrated correctly 

Re-calibrate speed setting

 

Speed set in the wrong 
Units of measurement

 

Change setting to proper 
Units.

 

Running belt not centered 

Running belt tension not 
Proper on the left or right 
sides of the running board 

Tighten the adjustment 
bolts on the left and right 
side of the rear roller (See 
page 11)

 

Computer not working 

Wires from the computer 
And bottom control board 
not properly

 

connected.

 

Check wire connections 
From the computer to the 
control board. 

Transformer is damaged 

If the transformer has 
become damaged contact 
customer service. 

E01: Communication 
failure 

No communication from 
console to control board 

Check wire connections 
From the computer to the 
control board, replace 
wires and/or control board 
if necessary.  

E02: Burst clash protection 

Incoming voltage is lower 
than 50% of the required 
voltage. 

Check the incoming 
voltage against the 
required voltage. Check 
wire connections to the 
motor. Check the control 
board, replace if 
necessary. 

E03: No speed sensor 
signal 

Speed sensor signal 
cannot be received by the 
control board. 

Check that the sensor wire 
is properly connected, if 
damaged replace wire. 
Check to see if the 
magnetic sensor is 
damaged, replace if 
necessary.  

E04: Incline failure 

 
The incline motor is 
damaged or the wire for 
the incline motor is not 
connected properly or has 
become damaged 

Re-connect or replace the 
wire for the incline motor. 
Replace the incline motor 
with a new one.  

24 

Summary of Contents for SF-T7604



























Reviews: