Sunell SN-TPC4201AT II User Manual Download Page 44

Page: 44 / 51

7 Technical Specifications

Thermal Imaging Integrated Network Camera

User Manual

Issue V1.0 (2018-05-10)

Type

Parameter

Description

WEB management

Embedded WEB service, remote
browsing and configuration over IE
browser

Remote upgrade and
maintenance

Support

Integration

Supporting the international standard
Onvif and the third-party protocol

Maximum user access
amount

Simultaneous access of 10 users to
the maximum

Interface
features

Network interface

RJ-45 and 10/100Base-T

Audio interface

1-channel audio input and 1-channel
audio output, supporting bidirectional
voice talkback

Alarm interface

Optional

Analog video output
interface

BNC, 75Ohm

Pan & tilt control interface

RS485

SD card connector

Micro SD card/HCSD card, 128 GB
to the maximum

System
function
features

Intelligent alarm

Mobile detection alarm, I/O alarm,
and disk alarm

Heartbeat mechanism

Support

Storage

Local storage, NAS storage, and SD
card storage

Privacy mask

5 areas with configurable size

Character display

Time, date, channel No., channel
name and user-defined characters

Security

Password protection, multi-level user
group management, user-define
permissions, and one-key reset

Reliability

Providing software and hardware
watchdogs and automatic fault
recovery

Physical
features

Power supply

DC 12 V

Power consumption

5 W

Summary of Contents for SN-TPC4201AT II




















































Search results

Summary of Contents for SN-TPC4201AT II

Reviews:

Related manuals for SN-TPC4201AT II

Brands by name

Popular brands

Sunell SN-TPC4201AT II, User Manual

Search results

Summary of Contents for SN-TPC4201AT II

Reviews:

Related manuals for SN-TPC4201AT II

Brands by name

Popular brands