Sunell SN-TPC4201AT II User Manual Download

Page: 42 / 51

7 Technical Specifications

Thermal Imaging Integrated Network Camera

User Manual

Issue V1.0 (2018-05-10)

Technical Specifications

Table 7-1 lists the specifications of the thermal imaging integrated camera.

Table 7-1

Technical specifications

Type

Parameter

Description

Detector
performance

Detector type

Uncooled infrared focal plane sensor

Sensing mode

Micro bolometer

Pixel

400x300

Pixel spacing

20 um

Response waveband

8-14 um

Thermal sensitivity NETD

50mK/F1.0,300K

Frame frequency

60 Hz

Video
features

Prime lens

8/15/25/35/50mm (optional)

Focusing mode

Manual

Field angle

43.6°*36.4°/24°*18°/14.6°*11°/

10.5°*7.8°/7.3°*5.5°

F value

1.0

Recognition distance

(Human body)

70/130/220/300/450 meters

Recognition distance

(Vehicle)

130/250/400/600/800 meters

Zoom lens

8/25/50/75 / 100 / 150mm (optional)

Focusing mode

Auto

Field angle

43.6°*36.4°/14.6°*11°o/7.3°*5.5°/4.
8°*3.6°/3.6°*2.7°/2.4°*1.8°

F value

1.0

Recognition distance

(Human body)

70/220/450/650/850/1300 meters

Recognition distance

(Vehicle)

130/400/800/1200/1600/2500 meters

Summary of Contents for SN-TPC4201AT II




















































Search results

Summary of Contents for SN-TPC4201AT II

Reviews:

Related manuals for SN-TPC4201AT II

Brands by name

Popular brands

Sunell SN-TPC4201AT II, User Manual

Search results

Summary of Contents for SN-TPC4201AT II

Reviews:

Related manuals for SN-TPC4201AT II

Brands by name

Popular brands