Sun Microsystems Sun Expert3D Installation Manual Download Page 36

Page: 36 / 54

Sun Expert3D Graphics Card Installation Guide • September 2000

lists the Sun OpenGL Version 1.1.2 for Solaris patches required for

Solaris 2.6, Solaris 7, and Solaris 8 operating environments.

The Sun Expert3D installation script installs these patches automatically, if required.
You can manually install or remove these patches by using

installpatch

and

backoutpatch

for the Solaris 2.6 operating environment, or

patchadd

and

patchrm

for the Solaris 7 and Solaris 8 operating environments.

■

To add a patch in the Solaris 2.6 operating environment, type:

■

To add a patch in the Solaris 7 and Solaris 8 operating environment, type:

Installing Sun Expert3D Software

Install the Sun Expert3D software from the CD-ROM provided with your installation
kit.

1. After installing the Sun Expert3D card into your system, boot your system at the

prompt:

2. Log in as superuser.

3. Insert the CD-ROM into the drive.

TABLE 3-8

Sun OpenGL Version 1.1.2 for Solaris

Patches

Solaris Release

Patch

Directory Location

Solaris 2.6

106735-16

/cdrom/cdrom0/OpenGL/1.1.2/Solaris_2.6/Patches

Solaris 7 (32-bit)

107104-11

/cdrom/cdrom0/OpenGL/1.1.2/Solaris_7/Patches

Solaris 7 (64-bit)

107105-11

/cdrom/cdrom0/OpenGL/1.1.2/Solaris_7/Patches

Solaris 8 (32-bit)

107104-11

/cdrom/cdrom0/OpenGL/1.1.2/Solaris_8/Patches

Solaris 8 (64-bit)

107105-11

/cdrom/cdrom0/OpenGL/1.1.2/Solaris_8/Patches

# installpatch

patchnumber

# patchadd

patchnumber

ok boot -r

Summary of Contents for Sun Expert3D























































Search results

Summary of Contents for Sun Expert3D

Reviews:

Related manuals for Sun Expert3D

Brands by name

Popular brands

Sun Microsystems Sun Expert3D, Installation Manual

Search results

Summary of Contents for Sun Expert3D

Reviews:

Related manuals for Sun Expert3D

Brands by name

Popular brands