background image

4

Open area track

Door pocket track

Open area track

Door pocket Track

Leading edge

Trailing edge

Connecting side

Connecting side

2 × 

I

5

Process holes for Trigger (leading edge).

I

5.5 

I

11.4 CSK

Process holes for track mounting.

I

5.5 

I

11.4 CSK

Process holes for track mounting.

Connecting side

Leading edge

Trailing edge

Connecting side

I

5.5 

I

11.4 CSK

Process holes for track mounting.

I

5.5 

I

11.4 CSK

Process holes for track

mounting.

2 × 

I

5

Process holes for Trigger 

(leading edge).

No use

No use

No use

When using 1260 mm track

When cutting from a long rail (2160 mm, 2760 mm, 3960 mm)

Track end to be 

connected

Track end to be 

connected

Track end to be 

connected

Track end to be 

connected

257

30

30

30 30

20

30 30

30 30

30 30

20

30

30

257

30

30

20

20

Track length for open area : Lo

Track length for door pocket : 

Lp

Track open area : Lo

Track length for door pocket : 

Lp

1

Cutting Track and Hole Drilling on Upper Track

When cutting, reinforce the 
track to prevent deformation 
at the cut section.

Do not cut the track on the 
side with three holes.

Caution

Caution

INSTALLATION PROCEDURE

Summary of Contents for LAMP FD80-H













Reviews: