Style selections 0293808 Manual Download Page 3

3

SAFETY INFORMATION

IMPORTANT

:  Read this owner’s manual carefully and completely before trying to assemble, 

operate, or service this heater. Improper use of this heater can cause serious injury or death from 

burns, fire, explosion, electrical shock, and carbon monoxide poisoning.
Only a qualified installer, service agent, or local gas supplier may install and service this product.

 WARNING

:  Do not store or use gasoline or other flammable vapors or liquids in the vicinity 

     of this or any other appliance.

 WARNING

: This appliance is for use with only the type of gas indicated on the rating plate. 

     This appliance is not convertible for use with other gases.

CARBON MONOXIDE POISONING

:  Early signs of carbon monoxide poisoning resemble the 

flu with headaches, dizziness, or nausea. If you have these signs, the heater may not be working 

properly. Get fresh air immediately! Have heater serviced. Some people are more affected by 

carbon monoxide than others. These include pregnant women, people with heart or lung disease, 

people who are anemic, those under the influence of alcohol, and those living in high altitudes.

NATURAL AND PROPANE/LP GAS

:  Natural and Propane/LP gases are odorless. An odor-

making agent is added to the gas. The odor helps you detect a gas leak. However, the odor added 

to the gas can fade. Gas may be present even though no odor exists. Make certain you read and 

understand all warnings. Keep this manual for reference. It is your guide to operating this heater 

safely.

 WARNING

:  Any change to this fireplace or its controls can be dangerous.

 WARNING

:  Do not allow fans to blow directly into fireplace. Avoid any drafts that alter 

      burner flame patterns.

 WARNING

:  Do not use a blower insert, heat exchange insert or other accessory not

     approved for use with this heater.

Due to high temperatures, the appliance should be located out of traffic and away from furniture 

and draperies. Do not place clothing or other flammable material on or near the appliance. Never 

place any objects in the heater. Heater becomes very hot when running heater. Keep children and 

adults away from hot surfaces to avoid burns or clothing ignition. Fireplace will remain hot for a 

time after shutdown. Allow surfaces to cool before touching. Carefully supervise young children 

when they are in the room with the heater.

Summary of Contents for 0293808


































Reviews: