OnAir 3000 Digital Mixing Console
4-6 Operating Elements
SW V3.0
Date printed: 31.10.08
Overload Indication, Analog Inputs:
As soon as one sample at an analog input reaches full scale, the overload
indicator is on for approx. 300 ms (the idea is that the probability of an A/D
converter reaching full scale without clipping is close to zero. Any full-scale
levels within the path are considered to be overloads).
Overload Indication, Digital Inputs:
Full scale modulation at a digital input is not considered to be an overload
– it is simply the output level of a source.
Overload Indication, REC/PGM Outputs:
If one sample of an output signal reaches full scale, the corresponding overload
indication is on for approx. 300 ms.
Auto Take-Over Indication:
The physical value and the internal processed value of the fader may be
different. This can be the case after routing, snapshot, or CAB changes – or
simply because a fader value has been changed with the GUI rotary encoder.
If the values are different, auto take-over mode is enabled. The direction in
which the fader knob has to be moved is indicated in the character display by
“FDR UP” or “FDR DOWN”. When the fader knob has been moved a bit,
the display changes to a numerical value such as “–15 UP” or “27 DOWN”.
When the fader position matches the internal value, “TAKEOVER” fl ashes
three times; the whole process is quite self-explanatory.
GRM
A gain reduction meter is provided in each channel strip. It is activated if the
channel’s compressor/limiter is active; it can also be configured to be active
in De-Esser mode.
Rotary Encoder/Channel Display
A rotary encoder and a corresponding key are available in every fader strip.
The function of these elements can be assigned/configured via the GUI or
the fader assign module. If the rotary knob in the fader strip or in the rotary
module is touched, the 8-digit channel label display shows the corresponding
value, depending on the selected function. Several functions are selectable,
such as input routing, input gain, balance, N–X level, AUX level, etc.
The corresponding key has an “Enter” or on/off function, depending on
the selected function.
Input Channel Routing:
To select an input signal for this channel, first turn the rotary to select an input
source group, followed by pressing . Then turn the rotary again to select
one of the input sources that can be routed to a channel. If the input signal is
routed to a different channel already, the label is marked with a dot. When
the desired source name shows up, press to assign the respective signal
to the channel.
Cal / Gain:
The rotary adjusts the mic input gain level or the calibration level for digital
inputs; the setting is displayed in dB. There is no function for the key in
this mode.
In case of remote microphone access the gain control automatically switches
over to calibration level control (V3.0)
Balance:
L/R balance or pan (-orama) is adjusted with the encoder and optically indi-
cated by the LED ring around the encoder knob. Using the key next to
the encoder, balance or panning is set to the adjusted value (on) or to center
position (off), while the adjusted value remains stored.
N–X Contribution Level:
The N
–
X contribution level of this channel to all N
–
X masters is set and
displayed in dB (“weighted N
–
X Feature”).
N–X Send Level:
If this channel is an N
–
X owner channel, the rotary sets the N
–
X send
level.
AUX Level:
The AUX contribution for this channel is adjusted. The corresponding key
activates the contribution to the AUX channel, the display shows the AUX
send level in dB.
Summary of Contents for OnAir 3000
