manualshive.com logo in svg

Stryker SmartPump Rx, Instructions For Use Manual

Share
Download
Stryker SmartPump Rx Instructions For Use Manual Download Page 9

 

Control Panel and Display 

9 

Features 

Convenient Preparation 

♦

 

The internal battery is charged automatically whenever the SmartPump is plugged into 
an AC power source. The internal battery is recharged to approximately 80% level within 
one hour. 

♦

 

The fully charged internal battery provides five hours of uninterrupted power. However, 
internal battery power is a safety feature and is to be used as a back up only. Always 
connect the SmartPump to an AC power source for normal operation.  

♦

 

Battery ‘saver’ technology keeps the internal battery charged. If the SmartPump is fully 
charged, then left ‘OFF(standby)’ and unplugged, the internal battery is kept charged for 
up to 30 days. 

♦

 

The SmartPump is center mounted to its recommended Stryker roll stand with pole. 

♦

 

Fill lines are attached to the positive locking connectors located at the bottom corners of 
the SmartPump.  

♦

 

At start-up, the SmartPump performs a self-test automatically and tests the pneumatic, 
pressure, display, battery, and processor systems. The SmartPump will alert the user via 
alarms, indicators and the display of error codes to assist in troubleshooting. 

Ease of Operation 

♦

 

The procedure timer and cuff target pressure may be set using simple, intuitive steps. 
Control buttons are clearly identified. 

♦

 

Inflation is initiated by pressing the 

Inflate 

button. 

♦

 

Deflation is initiated by pressing and holding the 

Deflate 

button for 1.5 seconds. 

Continuous, Real-time Monitoring  

♦

 

The large, bright, backlit LCD display shows total elapsed cuff inflation time and cuff 
pressure (mmHg). The displayed time format is user selectable: minutes or hours and 
minutes.

 

 

♦

 

Audible control alarms and flashing graphical symbols identify conditions requiring 
attention. 

Accessory Information* 

Description REF 

Roll Stand with Pole …..…….………………………….…………..5920-013-000 
Tubing, Stockinettes, Fill Lines, and Adapters .………………..5920-xxx-xxx Series 
Disposable Tourniquet Cuffs ………………………..….…………5921-xxx-xxx Series 
Non-sterile Reusable Tourniquet Cuffs…..…………….………..5922-xxx-xxx Series 

*Contact your Stryker sales representative for a complete list of accessories.  

 

Summary of Contents for SmartPump Rx

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands