manualshive.com logo in svg

Stryker SmartPump Rx, Instructions For Use Manual

Share
Download
Stryker SmartPump Rx Instructions For Use Manual Download Page 11

 

Control Panel and Display 

11 

Low Battery Power Alarms 

If a ‘low battery’ alarm condition occurs, connect the SmartPump to AC 
power as soon as possible. If AC power is unavailable and the internal 
battery becomes fully discharged, the SmartPump will maintain cuff 
pressure. Manual cuff deflation is required.

  

•

 

If 30 minutes of internal battery operating time remain, the 
following will occur: an audible alarm, the 

Alarm Indicator Mute

 

button will flash red and the battery charge icon will blink. The 
alarm may be muted for 15 minutes. 

•

 

If 15 minutes of internal battery operating time remain, an audible 
alarm will occur. The alarm may be muted for one minute, 
indicating the battery is ‘minutes’ from full discharge. 

Maintaining Internal Battery Charge 

When the SmartPump is plugged into AC power, its internal battery is 
charging automatically.  

The SmartPump control panel indicates battery-charging status as 
follows: 

 

Battery Charging Symbol: 

The segments of this symbol illuminates sequentially 

and repetitively while the internal battery is being charged. This occurs when the 
SmartPump is connected to an AC power source. Once the internal battery is 
fully charged, all of the segments are lit.  

 

Battery Power Symbol: 

The segments of the battery power symbol are lit to 

indicate the level of battery charge during internal battery operation. For 
example, three segments lit indicate a charge level of approximately 80%. 

 

AC Power LED Indicator: 

Illuminated green whenever AC power is applied to the 

unit.  

 

Battery Charge LED Indicator: 

Indicates battery charge status. The indicator 

operates when connected to AC power and the SmartPump is on or off. 

♦

 

Green (steady):

 internal battery is fully charged, in trickle or slow charge 

mode. 

♦

 

Yellow (blink):

 internal battery is in fast charge mode and may require one 

hour to reach an 80% charge level. 

♦

 

No Light:

 internal battery is not charging; AC power may not be present. if 

AC power is present, there may be battery charge circuit failure or internal 
battery failure. 

 

Summary of Contents for SmartPump Rx

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands