manualshive.com logo in svg

Stryker SmartPump Rx, Instructions For Use Manual

Share
Download
Stryker SmartPump Rx Instructions For Use Manual Download Page 16

 

Control Panel and Display 

16 

Display Indicators 

Status Indicators 

 

Default Display:

 Illuminated when the time and pressure are set for 

the default target values. 

 

Ready: 

All components are functioning normally and the unit is ready 

to use.  

 

Battery Charge Status: 

Indicates if battery is charging (bars light 

sequentially) or battery charge level (when running from battery). 

 

IVRA Lock: 

Indicates whether IVRA is locked or unlocked. This control 

provides accidental cuff/bladder deflation protection. 

 

 

 

H: MM 

or

 MINUTES:  

Indicates time format in use. 

 

Deflation: 

Indicates corresponding cuff is deflating or deflated. 

Alarm Indicators  

 

Service Required: 

When the SmartPump detects a condition that 

requires service, a service code with a wrench is displayed on the LCD 
and an audible alarm will occur. Note the code and call Stryker for 
assistance: 1-800-253-3210.

 

 

Caution:

 When an alarm is detected, the ‘Alert’ triangle is displayed, 

and either the time or pressure value will blink. DO NOT proceed until 
the alarm condition is resolved. Failure to comply may result in patient 
injury.

 

 

Audible Alarm:

 Indicates when the SmartPump is in an alarm 

condition and the audible alarm has been triggered.  

 

Alarm Muted:

 Indicates when the SmartPump is in an alarm condition 

and the audible alarm has been muted.  

Summary of Contents for SmartPump Rx

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands