Stryker 6516, Operation Manual

Page: 47 / 70

P Po ow we err ttyyp pe e O Op pe erra attiio on na all
vvo olltta ag ge e rra an ng ge e
F Frre eq qu ue en nccyy M Ma axxiim mu um m
ccu urrrre en ntt d drra aw w
S Stta an nd db byy ccu urrrre en ntt
d drra aw w
L Lo ow w vvo olltta ag ge e
ssh hu utto offff
AC 100 to 240 VAC 50/60 Hz 1.20 A 0.05 A N/A
DC 12.5 to 16 VDC N/A 4.16 A 0.20 A 10 VDC
IIn nsstta alllliin ng g tth he e S SM MR RT T cch ha arrg ge err
When installing the S SM MR RT T charger, place the S SM MR RT T charger in an environmentally controlled location that is:
• Free of excessive dust and moisture
• Kept within a constant temperature range. An allowable temperature range is 43 °F to 88 °F (6 °C to 31 °C). The optimal
temperature range is 65 °F to 75 °F (18 °C to 24 °C).
• Readily accessed for use
Locate and maintain the power supply and power cords to minimize the risk of damage and inadvertent disconnections.
IIn nsstta alllliin ng g tth he e o op pttiio on na all m mo ou un nttiin ng g b brra acckke ett
W WA AR RN NIIN NG G
• Always have a certified mechanic, familiar with ambulance vehicle construction, install the optional mounting bracket
and the S SM MR RT T charger.
• Always mount the S SM MR RT T charger to the optional mounting bracket in an enclosed cabinet and out of patient reach
during transport to comply with established crash test standards.
• Always make sure that the optional mounting bracket is securely attached to the surface.
To install the optional mounting bracket (Figure 28):
1. Use the S SM MR RT T charger mounting bracket as a template to mark the location of the mounting holes (A) at the area where
you will install the mounting bracket.
2. Position the mounting bracket, making sure that the:
a. Spring tab (B) is located at the rear of the S SM MR RT T charger.
N No otte e -- When mounting the bracket to a vertical surface, the spring tab should be horizontal with the spring tab point
to the left (Figure 28).
b. Power cord easily plugs into the rear of the S SM MR RT T charger.
c. S SM MR RT T charger slides from front to back to connect to the bracket after mounting.
d. Bracket is installed correctly for the ambulance or station location:
A Am mb bu ulla an ncce e llo occa attiio on n S Stta attiio on n llo occa attiio on n
• Secure the bracket to a horizontal structural support
surface or shelf using size #10, grade 5 screws
minimum (not supplied).
• Make sure that the selected mounting surface is strong
enough to securely hold the S
SM MR RT T charger and S SM MR RT T
Pak during transport.
• Locate the bracket in an enclosed cabinet and out of
patient reach during transport.
• Allow for easy S SM MR RT T Pak installation and removal.
• Locate the power supply within reach of the power cord.
• Secure the bracket to a horizontal or vertical structural
support surface using size #10, grade 5 screws
minimum (not supplied).
• For vertical installation, position the mounting bracket
so the spring tab is directly below the mounting screws,
so the S
SM MR RT T Pak remains supported by the S SM MR RT T
charger even if the release button is accidently pressed.
• Allow for easy S SM MR RT T Pak installation and removal.
• Locate the power supply within reach of the power cord.
6516-209-001 Rev D.0 43 EN