background image

General Technical Description

3 — 7

02_0461_0802GB

The technical data and characteristics which follow relate to
Strocomp compressors.

Strocomp 433

Strocomp 656

Strocomp 864 / 865

Dimensions

Length:

840 mm

840 mm

900 mm

Width:

470 mm

470 mm

550 mm

Height:

530 mm

530 mm

620 mm

Weights

Actual gross weight:

67 kg

64 kg

71 kg

Performance data

Engine:

Electric motor

2.2 kW

at 1500 rpm.

Electric motor

3.0 kW

at 1500 rpm.

Electric motor

2.2 x 2 kW

at 2800 rpm.

Maximum delivery pressure:

max. 10 bar

max. 10 bar

max. 10 bar

Intake:

400 l/min

600 l/min

800 l/min

Output:

300 l/min

450 l/min

550 l/min

Tank capacity:

2 x 5 l

2 x 5 l

2 x 5 l

Compressor cut--out pressure:

max. 10 bar

max. 10 bar

max. 10 bar

Compressor

above

Compressor cut--out pressure:

max. 10 bar

max. 10 bar

max. 8 bar

Compressor

below

Compressor start-up pressure:

7 bar

7 bar

8 bar

Compressor

above

Compressor start-up pressure:

7 bar

7 bar

7 bar

Compressor

below

Relief valve blow-off pressure:

11 bar

11 bar

11 bar

Sound pressure level:

xx dB (A)

xx dB (A)

xx dB (A)

Inclination angle in longitudinal
direction:

max. xx

˚

max. xx

˚

max. xx

˚

Inclination angle in transverse
direction:

max. xx

˚

max. xx

˚

max. xx

˚

Continued next page

3.5

Technical data

Summary of Contents for Strocomp 433









































































































Reviews: