manualshive.com logo in svg

Stratus ftServer 2900 Series, Planning And Installation Manual

Share
Download
Stratus ftServer 2900 Series Planning And Installation Manual Download Page 84

Installing PDUs (Optional)

9-6

Stratus ftServer 29x0, 49x0, and 69x0 Systems: Site Planning and Installation Guide

(R786)

Installing PDUs (Optional)

Power distribution units (PDUs) are an optional component. 

If you have 

not

 ordered PDUs from Stratus, skip this section and continue to 

“Installing a System Chassis” on page 9-11

. 

If you 

have

 ordered PDUs from Stratus and want to install them at this time, see:

–

“PDU Components”

 

–

“Installing PDUs in a Cabinet”

 

To connect the PDUs to AC power, see 

“Connecting Systems to Power Through PDUs” 

on page 11-6

.

PDU Components

The PDUs are ordered and shipped in pairs. Each PDU is shipped with mounting 
brackets attached. 

Verify that you have the components shown in 

Figure 9-4

 for your PDU, and inspect 

the components to ensure that they are not damaged. If you notice damage, contact 
the 

Stratus Customer Assistance Center (CAC) or your authorized Stratus service 

representative

.

Summary of Contents for ftServer 2900 Series





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands