manualshive.com logo in svg

Stratus ftServer 2900 Series, Planning And Installation Manual

Share
Download
Stratus ftServer 2900 Series Planning And Installation Manual Download Page 101

Installing the System Enclosures

Installing the System in a Cabinet

9-23

2. Attach the bezel.

a. Facing the front of the system, hold the bezel so that the LED light pipes inside 

the bezel (number 1 in 

Figure 9-19

) are on the right. Align the light pipes with 

the four front-panel system LEDs.

N O T I C E

The bezel light pipes extend about 0.25 in. (0.635 cm) out 
from the inside of the bezel. Be careful not to bend or hit 
the light pipes when installing the bezel. 

b. Holding the bezel in front of the mounting rails, align its ball-stud holes with the 

ball studs (number 2 in 

Figure 9-19

) on the sides of the system (two on the left 

side and two on the right). 

Figure 9-19

 shows the front of the system, with the bezel aligned with the cabinet 

for installation.

Summary of Contents for ftServer 2900 Series





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands